Leaderboard

Inviato dal mio iPhone utilizzando Tapatalk

Another new one in. This time from Mary. Hopefully I keep it for more than a few weeks. Initial impression is damn good. Titanium is nice and light. At 45mm. It’s a beast but most breitlings are I took off the gray ballistic Nylon/rubber strap because I cut it too short when sizing.. put it it on this distressed leather from gunny

This again... Sent from my iPhone using Tapatalk Pro

I agree. I don't bother to peruse it anymore. The old format was much more user friendly.

Have to agree... B

Sent from my Lenovo P2a42 using Tapatalk

From when I bought. http://www.ebay.com/usr/camlnn? Sent from my iPhone using Tapatalk

You can not contact the DarkLord unless you have someone he has dealt with to vouch for you.

Sub, gmt, Daytona. Sent from my iPhone using Tapatalk Pro

The V6S that I picked up, the one that had the real LV bezel, and the owner had the real hulk dial that he had not installed yet, is not bad. Someone took the time to engrave it. It has tones a good things. Few things were mis represented but that wasn't the fault of the guy I got it from. He was told that the crystal ring was real. The bezel was, but he said the bezel never rotated right. Well the nylon washer was pressed on the noob ring. I don't know if you guys know what the difference between the noob and the real rolex crystal rings are? I can post pics, but lets just say that the real rolex crystal ring, the top is skinny and that is where the nylon gasket rides on and holds on too. On the noob its the opposite. The top is larger on the noob and the bottom is where the noob nylon washer fits. That is why if you look at a real bezel assembly the washer is higher and smaller than the noob. But someone pushed this sucker onto the noob one. Now normally you can sand down a noob crystal ring and get the real bezel too fit the tip of the the noob one, or just replace it with a real one, which what the prior owner was told was done. But all in all the case is a very nice V6S, well engraved 3135 case. It has a real crystal. It came with a very nice actual Yuki that Craig serviced and it has a full auto winding bridge and rotor. It is running very well. it has a real 704 crown. It has real 97200 bracelet minus the clasp. Which is a bonus. I just ordered the 116610 hands yesterday I should have them Tue or Wed. Only thing I am wondering is if I should throw in a real 3135. I think I will because I want too keep this watch. I love my 116610LN. So I am going to put in a real crystal ring, and real bezel and the real dial. The only thing on it that wont be Rolex would be the nice V6S case and the clasp. Fun Fun.

Sent from my iPad using Tapatalk Pro Sent from my iPad using Tapatalk Pro Sent from my iPad using Tapatalk Pro

Thanks MOAB! [emoji106] [emoji38] Sent from my SAMSUNG-SM-G870A using Tapatalk

Well, I'm no Breitling expert, but I have some experience with PAM Daylights, I have put together few of them - A7750 3-6-9, A7753 and ETA 7753. So, here are few factoids about A7753 issues: 1. A7753 and modifed 3-6-9 A7750 have different height, and consequently different crown position - so cases are unfortunately not compatible, not saying it is impossible to put A7753 in A7750 3-6-9 case, but there must be some case modding involved 2. strangely enough, A7753 CAN take A7750 date wheel, and with A7750 date wheel, dial can also be taken from A7750 3-6-9 movement - for anyone not believing this I have picture attached of A7753 with A7750 date wheel installed 3. A7753 does not have possibility of setting date by going forward-and-backward around midnight because movement "maker" decided to save probably around 0,05 US$ and used date indicator driving wheel from 7750 movement instead of producing 7753 specific one - so, with this new part produced A7753 would have this possibility (same as ETA 7753). I hope this clears some of questions posted here. regards