capice Posted May 3, 2018 Report Share Posted May 3, 2018 On 2/20/2018 at 10:06 PM, automatico said: "Ruby reply today , 1680 case is 680$+50$ custom engraving+shipping." Just for fun, here are some of my cases with prices from the past: March 2011 - like new Yuki 1680 case...$420 from 'Stilty'. Traded it for a like new Phong 1655 case/dial with a member. Still have the 1655 case...stalled out for a long time by GMT movement parts search. Finally have all the parts...around $2500 so far including 1575 movement/GMT parts etc. August 2011 - used DW 5513 case, no case back...$50. Put a 'River' case back from sapphire Exp II and Clark bezel kit on it. Had a 1520 with Yuki dial in it for a while. Put the mvt in an MBK 5513. Still have the DW case. March 2012 - two new MBK 1680 watches from Narikaa...$800 for the pair, delivered. Put a 1575 and Yuki dial in one case for a while, other watch is still complete. One had a nice 93150 bracelet with hollow mid links, other had 93150 with solid mid links. Dials were Ok but had been roughly ground down to fit in 26.0mm dial seat. Machined the dial window for the 26.5mm 1680 dial. 2011/2012 - about 10 new assorted DW cases, some 5513, some 1680, some unmarked. Paid $150 to $200 for them. All are 1680 spec. Still have them. A lot of posts probably still up about them. September 2013 - one new IG44 1680 case from a member, $300. Best finished case of them all (that I have). The lugs have a slight 'canoe' shape (side view). Have a no hack 1575 and early genuine 1680 dial for it...the mvt/dial combo is in a DW case now. May 2014 - one 5513 and one 5512 case from Yuki plus one 'free' dial...$1100 for it all. Very good cases. Still have them. January 2017 - complete new MBK 5512 watch with 2836 etaclone and bracelet (oyster with riveted on side plates and solid links) from RWG member...$400. Put a Yuki dial and rolex 1570 in it. Notes: All MBK cases (5512/13, 1680) that I have are genuine rolex 1680 spec except they are made for a 26.0mm dial. If you make a 5512/13 with rolex 15xx movement you will need to use a 1575 date calendar spacer, center wheel, and cp. All DW cases (5513, 1680) that I have are genuine 1680 spec and all have a dial seat/window made for a 26.5mm dial. If you make up a 5512/13 you will have to use the date parts same as with an MBK case and there will be a space between the outer edge of the dial and case because of the 1680 spec 26.5mm dial and 26.0mm 5512/13 dial. I have seen pictures and read about early genuine 5512 with a space showing. Someone could make up a pretty good early 5512 with the dial gap and PCG and the rounded sides would add to the character. http://www.network54.com/Forum/207593/thread/1468292473/last-1468326320/View+All DW cases are high quality but the sides are rounded like a DJ, not flat, giving them an 'aged' look. The lug holes may be a hair too close to the lug tops when drilled out to 1.3mm or so. The case necks are a hair too small and it is hard to find a 1680 crystal that fits exactly. Making up a 5512/13 is not as bad because T19 crystals come in many sizes (GS crystals for example). DW watches came with 'spring wire' bezels and need a Clark, ST etc. bezel kit. The engraved numbers are Ok but many are unmarked. Some DW cases have undersize case back threads...oem is 30.9mm, some DW are 30.4mm. This is Ok as long as you have a set. MBK cases are very high quality but have laser engraving. In my experience Yuki cases are first class quality, same goes for my one Phong 1655 case. IG44 is hard to beat but IG44 is looong gone. I would spend the $$ on a good case if you want a watch to keep. Get one that is OEM spec so if you decide to put a genuine movement in it now or later. A Yuki etc. case with good dial and genuine movement will probably cost between $2200 and $2700 now because of jacked up prices. You could start out with an ETA 2846 or something and dial made for an ETA then go with a genuine movement later if you want something to wear while looking for a genuine movement etc. Be a good idea to stay away from 'big crown' projects with 1030 base rolex movements because of high $$ parts. The rolex 15xx parts situation is not too bad...yet. ETA is a LOT cheaper. Here is the info on one of my MBK 5513 projects a few years ago, 2011 or 2012 iirc (I have posted this before). It ended up costing about $1300. I still have it but it is apart. $300 or less for case (can not remember exactly) $102 for Yuki dial $25 for TC tube and crown $12 for ST hands $650 for 26 jewel rolex 1520 mvt $20 for mainspring etc $0 for c/o (did it myself) $85 for fake 358 hoods and put together '93150' bracelet, also have a folded oyster from 'Mary' that adds up to about the same $12 for GS crystal $68 for ST bezel kit (better fit than MBK bez with the GS crystal that was used) $25 misc...springbars, gaskets, case screws etc Had to use a 1575 date center wheel/cp and calendar spacer on the 1520 because the MBK 5513 case is made to 1680 spec, not 5513 spec. Extra cost is included with movement. The center sweep sec pivot is the same on 1520 and 1575, the 1575 second hand has a longer tube. Tnx but not mate,....now you have infected me with this horrible bug....😅 Quote Link to comment Share on other sites More sharing options...
cheld Posted May 23, 2018 Report Share Posted May 23, 2018 On 4/10/2018 at 10:57 PM, calvin951121 said: In production! Please wait! Sent from my iPhone using Tapatalk Pro Are you also making an Open 6 & 9 date wheel for gen 3135? Quote Link to comment Share on other sites More sharing options...
aprolexlover Posted June 1, 2018 Report Share Posted June 1, 2018 Anyone has any other contacts besides Phong, MQ, Ruby, Dung Chrono? Im looking for a 6542 case back, and Ruby has recently raised her prices by quite a bit. She is asking for $300 for a case back!!!! Need some help here. Quote Link to comment Share on other sites More sharing options...
pompompurin Posted January 10, 2019 Report Share Posted January 10, 2019 On 6/2/2018 at 12:52 AM, aprolexlover said: Anyone has any other contacts besides Phong, MQ, Ruby, Dung Chrono? Im looking for a 6542 case back, and Ruby has recently raised her prices by quite a bit. She is asking for $300 for a case back!!!! Need some help here. try yodog and tripdog on rwi. They seem to be able to source their own vietnam parts Quote Link to comment Share on other sites More sharing options...
RickFlorida Posted August 22, 2019 Report Share Posted August 22, 2019 On 7/31/2017 at 11:45 AM, lcz.79 said: Well done my friend...!...i use Dung's Dials usually...i Think is chipper and a little bit better quality..but get one more Dials supplyer is a good things....?thanks for share it with us... Who is Dung and how do I find him? I'm looking for a 5513 dial. Quote Link to comment Share on other sites More sharing options...
vette63 Posted March 27, 2021 Report Share Posted March 27, 2021 On 8/22/2019 at 7:30 PM, RickFlorida said: Chi è Dung e come lo trovo? Sto cercando un quadrante 5513. @dung was on ebay until 4 YEARS AGO , NOW NO Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.