-
Posts
130 -
Joined
-
Last visited
Posts posted by watchguy51
-
-
-
Yep they are polished. Was it worth €70 delivered?
Sent from my iPhone using TapatalksSic
Unfortunately not. Worth about €20 + shipping.
-
I'm also more into sports watches. The Vacheron 6782, one of my favourite references, used this movement. I think it'd be nearly impossible to get parts though. However, there are plenty of Vacheron dials on eBay... I'd just build a completely custom piece with this movement and a VC dial.
-
-
To all the modders around the world:
I am working on designing my own watch, which is partially based on a sub mid case. I need to have a prototype put together ASAP, and the factory I'm working with is taking its time.
Does any modder have a sub midcase that they can reshape for me, whether it be a 16610, 1680, 5512, or 5513? Even if it is from a canal street grade rep, it may be fine.
The crown guards would need reshaping, the midcase would need to be thinned, and the lugs would need some reshaping a bit too.
Who can offer some assistance with this?
Thanks!
-
Thanks! Good to know. And how do they slot in exactly? Do they sort of "clip" in?
Yes. It requires a lot of sanding normally. If you have a dremel and patience, you can do it.
-
I'm looking to use a champagne date wheel for a project (a Seiko actually), and I was wondering if it's possible to take a date wheel for another watch, and modifying it to fit.
-
I was in contact with him, letting him know it was full of aftermarket parts. The conversation was pretty civilized and I think he took it down himself.
-
-
The dial sizes on subs has been 26-28mm in the various eras. I was wondering how big the dial opening is vs how much of the dial gets covered. Anyone measure?
-
just checked the site and found my answer.. the seagull st-25.. i guess they just pulled off the rotor and put the nice plate over it
anyone know what movement they used as a base for this? with the full balance bridge
-
anyone know what movement they used as a base for this? with the full balance bridge
-
These are the measurements I'm looking for:
Width of the individual lugs at key points
Width of the crown and the gap between the crown and the case.
And the diameter of the crown is 7mm I believe?
-
amazing build, a grail watch for me
-
-
bump
An [hopefully] the last question, what is the width of the lugs at their thinnest and thickest points? Thanks again, this is all very useful!
-
Anyone know if you could replace the whole balance with gen? To have a proper free-sprung balance wheel on these would be great.
-
An [hopefully] the last question, what is the width of the lugs at their thinnest and thickest points? Thanks again, this is all very useful!
-
Also, are the pointed crown guards angled more from the top than at the bottom? Or are they symmetrical? And how far do they protrude?
-
Thanks so much for the info. Do you have the width of a lug at different points?
CGs are 5.25 mm thick (dial to case back) at the base
-
Thanks you. The more details, the better. The length and width of the crown guards, the thickness of them on both ends... I'd like to be able to draw up a proper diagram
41.6mm
-
I have an interesting project in the works right now, and I was wondering if anyone has the dimensions of a Rolex 5512/13 w/ pointed crown guards... or a gen/phong case to measure? I need every dimension of the mid-case and crown.
Also, the dimensions of a Helenarou 6538 bezel [notches] would be very useful.
Thanks everyone!
-
Gen? Thanks for the pic
-
Thanks!! Good info
Which factory makes (made) the Yuki 3135?
in The Rolex Area
Posted
I'll revive my old thread here from a couple years back... still wondering about this