-
Posts
29 -
Joined
-
Last visited
Posts posted by Mark_zijn
-
-
Thanks for the info Timelord and Automatico! I will definitely look in to it. Looks like it is going to be a bigger build than just swap a bezel and a crown. Luckily I find hunting for parts just as much fun.
-
I had, imho, the perfect Franken 16610 but is sold it a couple of years ago. And I miss it dearly so I want to build another one. What is the beste base to start from? I noticed some dealers aren't around anymore, so where to get one?
thanks in advance.
-
Its easier to get the correct 555 endlinks
-
For a couple of reasons in want a new bezel for my 116610LN, but where can I find the best one? Any help to point me in the right direction is greatly appreciated!
-
2 hours ago, mymanmatt said:
What movement are you using?
After some research I think its a seagull st-6...
-
4 hours ago, automatico said:
"I’m looking for Hr = 1.34mm, Min = 0.835mm, sec = 0,22mm."
Here are some hand sizes for common rolex movements:
1210/1215 manual wind 1.30 x 0.85 x 0.20mm
1530/1570 auto 1.20 x 0.80 x 0.20mm
3035/3135 auto 1.40 x 0.95 x 0.22mm
Looks like the 1210/1215 is close and reference 6694 models with 1210/1215 were 34mm same as a rolex 15000 oys perp date model. The 1530/1570 minute hand is close too.
It is easier to slightly enlarge a hand hole than shrink it down. You can broach the hole out a little bit if needed but closing a hand hole can be tricky. If there is a slight hub on the bottom side of the hand, I close the hole by putting the hub in the proper 'WW' lathe collet and squeeze it down a bit with the draw bar wheel. Without a lathe and proper collets you can use a pin vise being careful not to squeeze it down too much. Try to use a pin vise that is nearly closed when clamped over the hand hub because it can make 'flutes' (ripples) on the hub if the jaws are too far apart.
If you go with a pin vise, practice on a few cheapo quartz hands first.
You can make a few 'broaches' by filing 3 or 4 flats on a tapered needle etc. You can rough cut the broach with a miniature file and finish it up with fine sandpaper on a flat surface.
Sweep second hands can be a pain if the tube needs to be enlarged because the tiny broaches for the job break very easily.
Something else...be careful that the sweep second hand is not too tight on the sweep second pinion because it can cause damage to the ss pinion or break a jewel if there is one at the bottom. Another problem if the second hand is too tight is the hand can pull off over the center tube rivet when removing it. It is very hard to get the hand back on the tube and still have it look good. I have pressed sweep second hands down over a pin to enlarge the hole but I remove the hand with brass tweezers by pushing the hand off the pin from the bottom side.
It's all easier than it sounds with a bit of practice, believe it or not.
One of these makes it even easier:
Man, thanks for the reply! Great stuff
-
I’m in the process of building a franken 15000 date. But as it turns out, I’ve blown all of my budget on gen parts, everything except movement and hands is gen. I have a movement laying around from a old rep that I wanna use, and just buy nice silver Date hands for it (hands are cheaper than a movement), but I can’t find the ones with the correct hole size... I’m looking for Hr=1.34mm, Min=0.835mm, sec =0,22mm. Any one who can point me in the right direction? Any help is greatly appreciated!
-
Wow! Thanks for the info!
I probably have to cut the dial feet anyway to make it fit a ETA
-
I recently bought got a gen rolex date 15000 case set, it came with everything except a dial, dut im wondering if a dial from a 1500 date will fit, so i can expand my search.
Also, is the hand length the same as a datejust?
thanks!
-
I have a 16610 with gen bezel and crown, Yuki bracelet and a Clark crystal.
Is is it worth it to upgrade to a gen crystal??
thanks
-
Looks like a Datejust II, 116300
-
I would love a set, or two, of the vintage DJ spring bars! If anyone could help, please let me know!
-
Thanks for all the feedback!
i think i keep the watch as is.
I will keep searching for the perfect 16200 to complete the trio 16030, 16200 and 116200
-
16 minutes ago, mymanmatt said:
what movement in your 16030
To be honest, I don't know...
i had a rep day-date laying around, took the day disc off, and it fits perfectly!
-
I was wondering if it is possible to convert my franken 16030 to a 16220?
I googled the differences between them, and the main differences (besides the movement) is the crystal. Can I just swap the plexi for a sapphire, or are the case and bezel too different?
If it's possible to switch the crystal, what is the part number and where can I find the best sapphire crystal?
Thank you!
-
17 hours ago, monkeypunch said:
Curious if you have actual Air-King hands or regular stick hands.
Unfortunately i have regular stick hands, but still searching for the correct ones who will fit an ETA...
-
Hi,
I'm planning on building a Air-King for the misses, but on a budget.
I have a gen case, gen dial, clone movement, aftermarket hands, all i need is a crown and a bracelet...
Where can i find a cheap gen 24-530-0 crown, or nice signed rep?
And who has the best signed 78350 bracelet, Yuki, Raffles, Riyi or ..... ?
Any help is appreciated,
all the best
Mark
-
On 8 May 2016 at 4:02 PM, alligoat said:
Certainly you could try going to a Rolex AD.
Or you could try these aftermarket spring bars from WSE
Rolex Date and Datejust pins are going to be thinner than the Sub spring bars- maybe 1.8mm thick. I just hate to think what Rolex would charge- hope it's not too outrageous! Also, you might check Clark's- Nostalgia-2000- on ebay.
http://www.watchmaterial.com/rolex-generic-spring-bars-sp-9280/
On second thought- you can't really walk into a Rolex AD if you're building a franken- what if they want to see the watch to sell you the spring bars? Here's bars from Watchmaterial.
Thank you so much! Exactly what I needed!
Bought the bars from WSE.
I needed a clasp spring bar (32-20681) for my 16030 built an went to a Rolex AD, no luck... They weren't allowed to sell parts, wanted to see the watch and where not helpfull at all.
-
Hi,
I'm right in the middle of building a franken 5500 Air King. I have most parts sourced, everything gen except the movement. Although I yet have to decide on which bracelet, rivet, folded or 78350...
But there is one thing I can't figure out, or find any info about: what are the correct spring bars?
Does anybody have the reference number, a picture or a description?
Any help would be appreciated!
Thanks
-
Thanks guys!
i'm looking into both! They look promising, although in riyi002's shop, everything is unmarked...
Rolex5512, i'm looking forward for those pictures and feedback!
-
Hi,
I'm looking for a nice rep 62510 jubilee bracelet for my 16030 datejust build, I'm hoping you guys can point me in the right direction...
I have looked on a famous action site, but they are all unmarked or gen, unfortunately I don't have the funds for gen...
Thanks!
-
Great tutorial!
Thanks to you i started my own build!
I'm in the middle of getting the parts and was wondering which spring bars you used.
thanks
What is the best 16610 at the moment?
in The Rolex Area
Posted
Thank for the info! I will look into all of the ideas!