level z

ok. good luck.

see the first diagram if you wanna try a DIY ... http://www.ofrei.com/page558.html

or if you have a spare first wheel, you could try to check if it can work ... very unlikely the fault is with the shaft/pinion of the first wheel ...

i think it would be easier to replace the CP ... if you are gaming for some DIY .. you can try repair the cp .. see link ... http://mb.nawcc.org/showthread.php?22811-Loose-cannon-pinion i will try to find some pictorial later when i have the time as i have to do some work now ...

you have to confirm the hands are loose when fitted. You can try slightly moving the hand after being fitted to confirm if it is loose. The CP is fitted to the first wheel in such a way that it is allow to slight "somewhat slip like a clutch" but not overly loose ... If the hour hand is moving normally and the minute is not, then you need a staking tool to "tighten" up the CP.

dont file/sand off the bottom of the minute hand ... you may end up with minute and hour hand rubbing each other due to lack of clearence between them. Get a cannon pin tat is 3.15 mm like here http://www.tztoolshop.com/page151.html however you can find such sligtly higher CP in asian 6497 like those in rep watch. I pretty sure at the back of my head there is a differnece between the 18 kbph and the 21.6 kbph .. gearing size is not the same. hope this makes some sense to you and able to help u. cheers lz

I dont know if you gals and guys seen this before .. here goes ... Men's Pearls of Wisdom

Need funds for watch parts so putting up floor oscillating fan for sale .. fully working oscillating condition, only zero speed speed selection possible .. asking cheap .. open to offers

this really make me laughed till i teared .. hope you bring you some laughter too ... http://www.youtube.com/watch?v=nmxjWYY2zCk"

+1 .. the best hand remover i used .. mine is AF swiss ...good stuff

Hi ... it was gotten thru Hont ... well this is tobacco and 177 is black dial ... my opinion is the 61 is uncommon as compared to 177 so will get more attention ... just my 2 cents regards lz

... fren refuse to accept payment and i dare not ask as a gift ... so it is on long term/permanent loan ..lol

thx guys .. glad that the diver can pull off a formal occasion ... does look good on the hornback ... white stitch would be best ... but being a beggar i can't chose ..LOL

Which looks better ? leather or rubber ... :beatahorse: With a Gen hornback (permanent loan from a fren) and after market 18 mm buckle with a gen deploy rubber on a gen buckle (permanent loan from the same fren)

just came in the mail ...

will try to get a shot of it... it is verified by spin as a gen 727 ... regards

movement is Genuine ... case is aftermarket mate .. regards

yes .. movement gen ... regards thx guys for the valuable inputs.. regards lz

Hi Rolex gurus ... need some input on value of a super franken 6265 with the following specs .. Basically the whole watch is genuine except for the all the hands... very good condition.. works well .. well loved and care for .... - Movement and casing are from Phong (Vietnam) - Bracelet bought in Hong Kong, Genuine (sized for 7 inch wrist 2 spare links) - All hands not GENUINE - Bezel & dial from VRF(Vintage rolex forum) - Movement recently overhaul by spin master Any information on it's value would be greatly appreciated. Please PM me if it is not convenient to list here. Thx guys. best regards lz

hi .. i have some of them in 22 mm or 24 mm ... polish or brush ... i send you a PM .. please let me know if you are keen. regards lz

Any experts here please advice if the power reserve indicator works on the current Pam 90 running the a7750 ? How is the overall quality n accuracy of this current model ? Lume ? Super or normal ? Thx in advance for any advice or info ... Best regards Level z

thx mate ....

got it from Hont .... here we go ... ..

came today in the mail .. a late self bought christmas present .. happy holidays to all .. best to 2013.... regards lz

......