pfran42 Posted July 17, 2008 Report Share Posted July 17, 2008 This is my first solo attempt at trimming CG's. It seems that my buddy that was over at my house a few days ago is far better at this than I am. Do I keep going or stop? Also any input on shape/angle would be greatly appreciated. Link to comment Share on other sites More sharing options...
highoeyazmuhudee Posted July 17, 2008 Report Share Posted July 17, 2008 i say keep going, and round it out a bit so its not such a straight edge. found this for you: ENJOY http://www.rwg.cc/members/index.php?showto...5712&hl=mod lots of pics for reference and a how-to method Link to comment Share on other sites More sharing options...
mjmurphy926 Posted July 17, 2008 Report Share Posted July 17, 2008 EDIT - Not sure how this got here. See next post below. Link to comment Share on other sites More sharing options...
mjmurphy926 Posted July 17, 2008 Report Share Posted July 17, 2008 i say keep going, and round it out a bit so its not such a straight edge. found this for you: ENJOY http://www.rwg.cc/members/index.php?showto...5712&hl=mod lots of pics for reference and a how-to method I don't mean any disrespect, and I'm certainly not a great modder like some around here, but I'm not quite sure what "round it out a bit so its not so straight edge" means. I think you want it as straight as possible with as sharp of inside of corners as possible (where the CG meets the case). I think this is the area where a lot of people have trouble. I was able to get that corner pretty sharp. Mine are by no means perfect, but I compared to gen and they are pretty close. I followed gio's tutorial. It's a great tutoral. It took me several days to get them where I was satisfied. Just take your time. Mine for reference: BTW - I would replace that perl next Link to comment Share on other sites More sharing options...
pfran42 Posted July 17, 2008 Author Report Share Posted July 17, 2008 I don't mean any disrespect, and I'm certainly not a great modder like some around here, but I'm not quite sure what "round it out a bit so its not so straight edge" means. I think you want it as straight as possible with as sharp of inside of corners as possible (where the CG meets the case). I think this is the area where a lot of people have trouble. I was able to get that corner pretty sharp. Mine are by no means perfect, but I compared to gen and they are pretty close. I followed gio's tutorial. It's a great tutoral. It took me several days to get them where I was satisfied. Just take your time. BTW - I would replace that perl next WOW!!! That looks amazing. I still have a little ways to go...Can you direct me to Gio's tutorial? I have been using the other one mentioned on this thread already and it does not show such sharp edges. As for the pearl, I lost it tonight but it turned up and I glued it in place already. It is aftermarket and looks a million times better than what came on it. Thanks for the feedback! Link to comment Share on other sites More sharing options...
pfran42 Posted July 17, 2008 Author Report Share Posted July 17, 2008 Never mind...you ARE talking about the same tutorial...my bad Link to comment Share on other sites More sharing options...
mjmurphy926 Posted July 17, 2008 Report Share Posted July 17, 2008 WOW!!! That looks amazing. I still have a little ways to go...Can you direct me to Gio's tutorial? I have been using the other one mentioned on this thread already and it does not show such sharp edges. As for the pearl, I lost it tonight but it turned up and I glued it in place already. It is aftermarket and looks a million times better than what came on it. Thanks for the feedback! Thanks. I should probably tell you though, that I did do something in addition to what I read in Gio's tutorial. Once I was happy with the amount of material removed, I noticed that the part I sanded was flat and didn't follow the radius of the inner part of the CG. So I took a strip of 220 wet/dry sand paper (the black stuff) and, with the crown in place, I ran it between the crown an CG (with the abrasive part toward the CG, obviously ). This not only rounded the flat spot to match the inner CG, but it also ensured that the gap was even on either side of the crown between the crown and CG. Two things to be careful of though...Be sure NOT to push the sandpaper down toward the watch case or you will cut a groove in the corner...And, be sure to remove the crown and clean/grease the gaskets when finished. Good luck, Mike Link to comment Share on other sites More sharing options...
highoeyazmuhudee Posted July 17, 2008 Report Share Posted July 17, 2008 this is what i meant by rounded VS straight edge. maybe yours are like this in person, just cant see it on the photo. CGs are a matter of personal opinion for most i think, so if youre happy thats all that matters. the gen shows like theyre rounded around the crown, and it appears the same in the tutorial. not like a pointy straight edge. Link to comment Share on other sites More sharing options...
pfran42 Posted July 18, 2008 Author Report Share Posted July 18, 2008 this is what i meant by rounded VS straight edge. maybe yours are like this in person, just cant see it on the photo. CGs are a matter of personal opinion for most i think, so if youre happy thats all that matters. the gen shows like theyre rounded around the crown, and it appears the same in the tutorial. not like a pointy straight edge. Nice illustration..I totally see what you mean...hmmm...I am going to AD tomorrow to clear my head and get a 3D look at them on the gen. Pics tell only 80% of the story. Link to comment Share on other sites More sharing options...
highoeyazmuhudee Posted July 18, 2008 Report Share Posted July 18, 2008 thats a GOOD IDEA. staring at contradictory pictures all day will make ya go insane. report back your findings : ) Link to comment Share on other sites More sharing options...
mjmurphy926 Posted July 18, 2008 Report Share Posted July 18, 2008 this is what i meant by rounded VS straight edge. maybe yours are like this in person, just cant see it on the photo. CGs are a matter of personal opinion for most i think, so if youre happy thats all that matters. the gen shows like theyre rounded around the crown, and it appears the same in the tutorial. not like a pointy straight edge. I guess it depends what gen pix you look at. The gens in my local AD look like this gen pic: That is what I modeled mine after. Rolex has a way of slightly changing things, like CG shape all the time. You're right, it's up to the individual to decide what they like best. I just went with what I saw in person. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now