Jump to content
When you buy through links on our site, we may earn an affiliate commission.
  • Current Donation Goals

Question about Hublot Big Bang and the pushers/dial


Zack G.

Recommended Posts

Hello everyone,

I am relatively new to this site and I just picked up a used HBB SS from another forum member. I had a quick question.

When I hold up the watch and I hit the lowest pusher, it seems that the dial itself moves when the pusher is pushed in? Is that normal? Does that mean the dial is not affixed correctly and is loose? The dial doesn't move around if I move the watch around, only if the pushers are pushed in.

Thank you for any feedback on this.

Link to comment
Share on other sites

Sounds like the mvmt is a little loose. Theres a couple of tabs that hold the movement into the case, pop the back and make sure they are tight.

You can see two at the bottom and one at the top in this pic of a SFSO.

ETAClose.jpg

Link to comment
Share on other sites

Sounds like the mvmt is a little loose. Theres a couple of tabs that hold the movement into the case, pop the back and make sure they are tight.

You can see two at the bottom and one at the top in this pic of a SFSO.

ETAClose.jpg

Upon closer observation, I noticed the dial and or movement is a little loose just by moving the watch around up and down. You can hear little "clicks" when the watch is moved up and down. I tried to do exactly as you described, however the same thing happens. The tabs were already pretty tight when I opened the case back. Is this just a faulty watch?

Edited by Zack G.
Link to comment
Share on other sites

Upon closer observation, I noticed the dial and or movement is a little loose just by moving the watch around up and down. You can hear little "clicks" when the watch is moved up and down. I tried to do exactly as you described, however the same thing happens. The tabs were already pretty tight when I opened the case back. Is this just a faulty watch?

When you checked the tabs and they were tight, was the movement still loose and moving around? Can you see it moving around through the display case back?

It sounds like the dial itself may be loose, but that leads me to more questions. How many tabs were there?

This could be a simple repair for your local watchsmith, $20-$30ish.

Pictures may help if you can post some. Movement side.

Link to comment
Share on other sites

When you checked the tabs and they were tight, was the movement still loose and moving around? Can you see it moving around through the display case back?

It sounds like the dial itself may be loose, but that leads me to more questions. How many tabs were there?

This could be a simple repair for your local watchsmith, $20-$30ish.

Pictures may help if you can post some. Movement side.

I believe there were only 2 tabs once I open the case back. There was one on the bottom, and then another one at the top (had to move the rotor a little to uncover that one).

If I bring this watch to a local watchsmith (at the mall, etc.), do you think they will be able to tighten it up somehow?

I am not sure if its the dial that moves or the movement (or if the movement and dial is one piece - when it comes to watches I am not very technical and don't know if they are attached to one another or not).

Thank you for your help.

Edited by Zack G.
Link to comment
Share on other sites

I also forgot to say that looking only at the dial visually, you can see that the dial moves only VERY LITTLE. However, when your holding the watch in your hand, or if its on the wrist you can definitely feel that something inside (dial and or movement) is loose.

Looking through the case back, its not noticeable visually that anything moves (I am not sure if the spinning rotor is throwing it off visually).

Thank You

Edited by Zack G.
Link to comment
Share on other sites

You could also email the dealer and see what your options are...

I purchased this watch used from another member here. However I am aware of that this HBB was one of the few that were produced and they came from Angus (PureTime).

I will email who I bought it from and see what they say.

I also brought it to a local watch repair shop today, however the watchsmith wasn't in, so I will try back tomorrow.

Thank You

Link to comment
Share on other sites

are you sure you're not just hearing the rotor move?

The dial is attached to the movement with dial feet. Little prongs that stick out of the underside of the dial and insert into the movement. Does the watch have a display case back? Watch for movement through it if so.

Link to comment
Share on other sites

are you sure you're not just hearing the rotor move?

The dial is attached to the movement with dial feet. Little prongs that stick out of the underside of the dial and insert into the movement. Does the watch have a display case back? Watch for movement through it if so.

I'm positive that its not just the rotor spinning which is causing the dial to move. I didn't get a chance to bring the watch in today since I was busy but I will stop by the local watchsmith this week and will report back. I hope this is a small easy fix (seems like something needs to be tightened inside - although I only saw 2 screws on the back movement when I open the case back and they seemed tight already).

Edited by Zack G.
Link to comment
Share on other sites

I had the same problem on a HBB I owned. It was the case/movement clamps. They were tight, but they were bent and would no hold tight against the case. I bent them slightly and it fit tight again.

Unfortunately I don't have the skills or expertise needed to try and attempt bending any clasps myself. I fear of possibly damaging something even more. However it didn't seem that those 2 clamps which I mentioned in my previous post were bent at all. They looked straight.

I tried again tonight and opened the caseback(mine is see through non Tuiga version). This time I figured I would try and simply put my finger on top of the rotor and apply a little pressure to the back of the rotor while I was holding the watch up directly facing me and while I applied minimal pressure with my pointer finger it seemed that the dial and movement didn't move at all.

It seems that it's like lacking some pressure against the rotor since applying minimal force helped. Offcourse it went back to being loose when I took my finger off the rotor.

I hope my explanation made some sense.

Thank you and I will report back after my visit to the watchsmith.

Edited by Zack G.
Link to comment
Share on other sites

  • 2 weeks later...

Just wanted to post a quick update. I took the watch in today finally to my local watchsmith and he told me that all of the tabs were nice and tight, etc. He said that the movement is a tad too big for the case, that is why it seems to "move around' somewhat.

Is this normal? Is this something that has to be taken into account for it being a rep?

I am really thinking of returning this watch to the seller, as it can get annoying at times and doesn't feel right.

Thanks

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...
Please Sign In or Sign Up