mymanmatt
-
Posts
1,244 -
Joined
-
Last visited
-
Days Won
9
Posts posted by mymanmatt
-
-
Ok, you need to calm down. The dial you saw for 1015E is a day-date 2 dial, not a 118239 dial. I can source about any dial you want, except glacier blue. Once again, that bracelet you have a link to is an 18239 bracelet, not a 118239. I have high quality cases and bracelets. I don't think you will need to do anything to them.
-
One other thing. As long as the mainspring assy and balance assy are out, If you happen to go just a little to far, you won't hurt anything. It will just be open space below the mainspring tub and the bal assy. You do want to secure the dial on the movement. You don't want it moving up and down. There is a grove cut under the rehaut that the dial sit's in, that will usually hold it in place. A couple of dial dots won't hurt though. Be sure you have a snug fitting movement ring, that's always a must.
-
All great pics. It's hard not to vote for the watch instead of the pic.
-
I think you should build this yourself. It will take some time but I'm sure you can do it. You're right, that glacier blue dial is nearly impossible to source. I also have matching day and date wheel overlays. Clark has a nice set of tudor hands. However be careful that you hour and minute post are high enough so the hands won't damage the dial. You can buy a taller cannon pinion. If you do, I have a long post sweep second so you don't need to change the center wheel. Good luck
-
The tip for my guy was the way phong finish's the case on the inside of the lug at the case in the corner. Rolex is a very smooth 1/2 round, phong's is slightly squared, and I mean slightly. A good comparison is a gen gold jubilee link compared to aftermarket. The gen has a rounded corner where the pin or screw goes through. The aftermarket does not.
-
The color of the dial in the picture is oyster. It's not silver, not champagne, and not white, its oyster. But that is only used on a gold watch. On a white gold they use rhodium or silver. Also the one in your picture is an 18238 old style. The 18239 is old style too, 118239 is new style. I carry those case and bracelets as well as the old style. Which ever one you build, DO NOT CUT THE FEET ON THE DIAL, you don't need to. Simply notch the movement ring at 4:30 and 10:30
-
Yes. They have several stores. The buyer in one store bought it thinking it was gen. It had a fresh 3135 gen movement and a for sure gen buckle. Gen dial, hands and crystal. Not 100% sure on the insert. After they buy watches they go to a central login department and that's when it was spotted But only after an extreme amount of checking.
-
You cant get any closer to the mainplate. Just BARLEY enough room. I use my dremel and just slot it instead of drilling a hole. Mark it, remove the bal assy, and the main spring, cover the movement and grind away with my little cutter wheel. So far, haven't messed up anything. LOL
-
The 180xx dial has feet at 4;30 and 10;30 You don't need to clip feet on a pres for any eta. You notch the movement ring. The datejust has feet at 2;30 or 2;45 I can really tell for sure, and 7;30. You can notch the baseplate at 7;30, but not 2;30. The problem at 2;30 is the yoke corrector. It will hit the foot of the dial and not allow you to set the time or date. The other dials that have feet in the 5;30 and 11;30 I think can be made to fit the eta baseplate. Never done it, but I think there is enough room.
- 1
-
So, one of my AD's bought what he thought was a gen 16610. Turns out it was a phong case complete. Anyone have an opinion on what the case is worth. It's complete with case, caseback, bezel, insert, case tube, crown, and crystal.
-
I have no idea on the hands. I have the dwo.
-
If you're looking for gen hands for an eta 2671, the gen 2035 hands will fit. The 2135 will not
-
I believe the feet position o the 1016 is different from the dj and pres. I believe there is enough room to notch the base plate under the balance assy and at the mainspring area. That remains to be seen.
-
First, it's not gold plated. It is wrapped. That means they put a layer of gold over the case. Depending on the thickness, it could have a lifespan of 20 years. Rolex did that on their 1500 cases in the 70's and 80"s. Gold plating will eventually wear off in the high rub areas. This case is gold wrapped, and if you like it, buy it. You will not be disappointed.
-
That does it. I'm getting one done for myself. You guys will hate this idea. 118239, diamond lugs, center diamond bracelet, diamond bezel, everything smooth engraved. I'm going to see if he can engrave a gen diamond dial. OMG
- 1
-
I like it!!! A lot!!!!!!!!!!!!
-
Damn, is he the next Bill Gates?
-
whoopy has 3 for sale in the parts section
-
Yes, that is typical of a bad reverse wheel. Be sure it is oil free
-
I'm not sure I fully understand what you are saying, but I think you mean the rotor is spinning when you wind it, correct? That is not normal and usually indicates a bad reverse wheel. The only fix is to replace it. OIL is NOT the solution, as many people think. So if someone tells you to oil it, that won't help.
-
Are you sure the date wheel is installed correctly? I'm just saying when you install a gen on a yuki, it's hard to get it exactly in place. Is the rotor maybe touching your caseback? Have you tried loosening the caseback a little to see if the sound goes away?
-
Great choice!
-
I think the bad name for sw is justified. Everyone I've seen needed to be replaced. And, they were new. I'm telling you, the quality of the parts in the sw is not good. That's my 2 cents.
-
That's freakin funny. More bull shit than I've seen on one page since the guys dog needed a hip replacement or something like that. He was asking for money on this forum LOL
The new rolex 40mm 2015
in The Rolex Area
Posted
Ok automatico, tell us what you really think. LOL I'm just kidding. My friend bought a new 1803 in 1969. Price $999.00 On sale $895. LOL That was a lot for a watch.