gplracer Posted July 31, 2009 Report Share Posted July 31, 2009 What is the safest way to get the acrylic bezel off of my DW 6263. I do not want to harm it but it is on tight. Link to comment Share on other sites More sharing options...
freddy333 Posted August 1, 2009 Report Share Posted August 1, 2009 Use either an un-serrated knife or a razor blade (a paint scraper works well since it has a handle to hold the blade) & carefully wedge it in between the bezel & case. Go as far as you can without force. Then rotate the watch & go at it at another location. Keep wedging the blade in around the circumference of the bezel until it loosens & eventually you should be able to remove it. Depending on how tight the bezel is, the process can take anywhere from a few seconds to 30 minutes. Be patient, careful & keep at it & eventually it will come off. Link to comment Share on other sites More sharing options...
gplracer Posted August 1, 2009 Author Report Share Posted August 1, 2009 Thanks Freddy Link to comment Share on other sites More sharing options...
gplracer Posted August 1, 2009 Author Report Share Posted August 1, 2009 Ok the bezel is off and the new crystal is on. I am a nervous wreck but it looks good. After I got the crystal on the first time I saw two small pieces of lint. I then took it off and did it again. Now all I have to do is put the bezel back on. My question now is do all of the bezels require sanding on the inside and how do I know? I am going to put the steel bezel on but I do not want to crack the crystal. Should I be able to put this on by hand or should I use a case press? How much tension should there be? My bezel slides on and off of my other dw with the stock crystal if that is any clue as to its size. It would have to be glued on if I was using the stock crystal. Link to comment Share on other sites More sharing options...
freddy333 Posted August 1, 2009 Report Share Posted August 1, 2009 My rule-of-thumb is that you should be able to press the bezel about half way down the side of the crystal by hand only (no tools whatsoever). From there, you would need a press to secure the bezel against the case. If the bezel can be pressed down all the way or removed by hand, it is too loose & will not press the crystal against the case walls sufficiently to keep moisture out. Unfortunately, aftermarket bezels are often either slightly too large or too small. There is not much you can do if your bezel is too large other than exchanging it for another (& keeping your fingers crossed that the next 1 is better). But if the bezel is too small, you can use a dremel (or your grinding tool of choice) to remove a SLIGHT amount of material around the inside circumference to get the dimension just right. VERY IMPORTANT - remove only a little material and then TEST IT on your crystal (mounted on the case). If it is still too tight, remove a bit more material & retest. If you remove too much material, you will be in need of a new bezel. Good luck. Link to comment Share on other sites More sharing options...
Chronus Posted August 1, 2009 Report Share Posted August 1, 2009 Will a Vietnam or a gen bezel fit with no problems with having to use dremels etc? Link to comment Share on other sites More sharing options...
gplracer Posted August 1, 2009 Author Report Share Posted August 1, 2009 Great tip Freddy, I like the 1/2 of the way down rule. This is a learing process for me. Link to comment Share on other sites More sharing options...
freddy333 Posted August 2, 2009 Report Share Posted August 2, 2009 Will a Vietnam or a gen bezel fit with no problems with having to use dremels etc? A gen should fit a gen case/crystal perfectly (following my rule-of-thumb), but I have never worked with a Vietnam-sourced Daytona bezel, so I cannot comment about that. Link to comment Share on other sites More sharing options...
Chronus Posted August 2, 2009 Report Share Posted August 2, 2009 A gen should fit a gen case/crystal perfectly (following my rule-of-thumb), but I have never worked with a Vietnam-sourced Daytona bezel, so I cannot comment about that. Thanks for the info. I guess if a gen crystal fits a DW (or Vietnam) case, then the gen bezel should fit around the crystal, so by extension, should hopefully fit the DW case. I would hope Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now