bummerh12 Posted October 3, 2011 Report Share Posted October 3, 2011 Hi Pam Modders Whats grit sandpaper should i use to achieve the brushed finish as shown on the pic. Or will a brushed Refinishing Pen do the trick? Appreciate the tips! Link to comment Share on other sites More sharing options...
PeteM Posted October 3, 2011 Report Share Posted October 3, 2011 Mate... there is so much info on this and a number of tips and methods... Far too many to relist here... but try doing a search because they are there... Hounddoggie also did a tutorial on his version but I think although the link is listed on here in the threads I refer to...the original thread is on RG.. Good luck Link to comment Share on other sites More sharing options...
bumroxas Posted October 3, 2011 Report Share Posted October 3, 2011 Dont use sandpaper... you'll ruin the profile of the cg. best for me is scotch brite, the harder you press the deeper the brushed effect. Link to comment Share on other sites More sharing options...
blbl Posted October 3, 2011 Report Share Posted October 3, 2011 is that the pam176 recently uploaded in the panerai facebook page? Link to comment Share on other sites More sharing options...
bummerh12 Posted October 3, 2011 Author Report Share Posted October 3, 2011 Mate... there is so much info on this and a number of tips and methods... Far too many to relist here... but try doing a search because they are there... Hounddoggie also did a tutorial on his version but I think although the link is listed on here in the threads I refer to...the original thread is on RG.. Good luck Thanks Mate.. Found the thread on WC! Link to comment Share on other sites More sharing options...
PeteM Posted October 3, 2011 Report Share Posted October 3, 2011 :thumbsupsmileyanim: Link to comment Share on other sites More sharing options...
sul Posted October 5, 2011 Report Share Posted October 5, 2011 (edited) You can use sandpaper also, no problemo Take CG off, take GC pinion off also if you like perfect final result. Put 800 or 600 sandpaper on your desk, put CG on sandpaper, press it down hard ( point is that your CG will not moving up and down only forward and backwards) and move CG with you finger (s) forward and back, long sweeps, not short ones. Result will be as gen ones. Steady hands are needed. If needed you can do one final sweep with nr 1000 sandpaper also or slightly with scotch brite. Usual problems are with this technique: -stripes on GC surface are not straight and even - moving direction was not right or sweeps were not long enough. -CG edged are slightly rounded- you did not press CG on sandpaper well ( equable)enough. It was moving up and down slightly. PS) less sanding and shaping is always better then more. Check always CG surface after every sweep. My 040 GC back side was done like that and I am happy with result, sorry don`t have any good picture but here it is: Edited October 5, 2011 by sul Link to comment Share on other sites More sharing options...
w0lf Posted October 5, 2011 Report Share Posted October 5, 2011 If you use sandpaper on tapered historic CG it will destroy the geometry. You can only fully refinish a 1950 CG that's flat on both top and bottom using this method. With a historic you can use sandpaper/emery bar only if you're finishing the bottom flat part. Also, the easiest method is not to not freehand it but rather use a ruler or a machinist angle as a guide to slide the CG along sandpaper. The only way to do the top curve properly would be to use a jig that will protect the taper. Otherwise using a scotch brite pad is your only recourse. Be very mindful of how aggressively you apply the brushing because you can also lose edge detail if you overdo it. the grit in the picture looks to be ~400. Link to comment Share on other sites More sharing options...
maxman Posted October 5, 2011 Report Share Posted October 5, 2011 I used a scotch brite(green/yellow) pad on my 250 cg....It came out better that expected. It was suggested that I use a slightly dampened pad...makes It easier to work with..... and go with the grade as best as possible. It was also suggested that I check the finish evey few swipes. I thought even the pin looked more flush when i was done....although.. that was probably just wishful drinking on my part. Mike Link to comment Share on other sites More sharing options...
bummerh12 Posted October 5, 2011 Author Report Share Posted October 5, 2011 Thanks for all the suggestions, very much appreciated. I decided to buy a brushed refurnishing pen. One problem i had was that there was a tiny scratch om the cg. Intructions on the pen was that it is able to remove minor scratches! Like what w0lf mentioned, for a historic cg that is tapered using a sandpaper is tricky. The refurnishing pen was a easier method. Will take some pics when i borrow macro lens from my friend. Cheers, Dan Link to comment Share on other sites More sharing options...
flin0310 Posted October 6, 2011 Report Share Posted October 6, 2011 (edited) I saw senior watchsmith refinished brushed CG and the method refer to below, 1. Screw off CG and lever pin, prepare two tools 1), big size #800 sandpaper 2), 30 cm length heavy thick ruler 2. Put CG on sandpaper and CG to case side (not the round side) touch ruler 3. Pull CG on sandpaper 5 ~ 10 times by one direction, then CG wills refinish likes the new one . Edited October 6, 2011 by flin0310 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now