Torques Posted December 10, 2006 Report Share Posted December 10, 2006 (edited) I had my watch 2 inches under the surface of my pool for like 1-2 seconds, then went inside and rinsed it off lightly in case of any chlorine. I then dried it well with a towel. Thirty minutes later I notice there is some misting under the crystal. I put the watch out in the sun, should that fix it? It's a Seadweller from one of the rip-off sites, ha ha, otherwise I like it. Edited December 10, 2006 by Torques Link to comment Share on other sites More sharing options...
Pugwash Posted December 10, 2006 Report Share Posted December 10, 2006 Thirty minutes later I notice there is some misting under the crystal. I put the watch out in the sun, should that fix it? You need to have the crown open if you're attempting this type of fix. Even then, this isn't likely to work, I'm afraid. Unfortunately, Reps aren't sold as water-resistant. Link to comment Share on other sites More sharing options...
Torques Posted December 10, 2006 Author Report Share Posted December 10, 2006 (edited) You need to have the crown open if you're attempting this type of fix. Even then, this isn't likely to work, I'm afraid. Unfortunately, Reps aren't sold as water-resistant. How do you get the crown open? I do have a case opener now, but I don't want to mess with taking out the crystal if I can help that, too much from now, just starting out. Edited December 10, 2006 by Torques Link to comment Share on other sites More sharing options...
ubiquitous Posted December 10, 2006 Report Share Posted December 10, 2006 Open the crown and throw the watch in a ziplock with a packet of silica. The silica will pull the moisture out of the watch... Link to comment Share on other sites More sharing options...
Pugwash Posted December 10, 2006 Report Share Posted December 10, 2006 How do you get the crown open? I do have a case opener now, but I don't want to mess with taking out the crystal if I can help that, too much from now, just starting out. Crown - the thing you use to set the time. You need to make sure that's as open as possible otherwise the water vapour has nowhere to go and will just rust the movement up. What watch is it? Link to comment Share on other sites More sharing options...
Torques Posted December 10, 2006 Author Report Share Posted December 10, 2006 Crown - the thing you use to set the time. You need to make sure that's as open as possible otherwise the water vapour has nowhere to go and will just rust the movement up. What watch is it? Seadweller, do you mean just pull it out as far as it will go? Link to comment Share on other sites More sharing options...
2005SUBMARINER Posted December 10, 2006 Report Share Posted December 10, 2006 like UBI said you need to open your watch & let it dry out for a few days .. once you take your watch apart , you should lube all the orings in your SD .. good luck .. Link to comment Share on other sites More sharing options...
Torques Posted December 10, 2006 Author Report Share Posted December 10, 2006 Seadweller, do you mean just pull it out as far as it will go? I found a little packet of silica and I put it in a baggy with the crown pulled out as far as it will go. How long might that take to fix. The water is very hard here, I hope if it dries it will not leave little water spots in there. Link to comment Share on other sites More sharing options...
Torques Posted December 10, 2006 Author Report Share Posted December 10, 2006 I'm glad I bought a Rolex caseback opener. When I started to unscrew, it was basically not on tight at all, maybe that's where the water came in. So I put the watch in the baggy with the silica with the back off. Would it hurt to blow some heat in there or just leave it in the baggy? Link to comment Share on other sites More sharing options...
vmena Posted December 10, 2006 Report Share Posted December 10, 2006 By experience, once water comes into the watch, unless you open it, remove the movement and dry it outside the case, the result will be a damaged movement for ever an ever... I'm glad I bought a Rolex caseback opener. When I started to unscrew, it was basically not on tight at all, maybe that's where the water came in. So I put the watch in the baggy with the silica with the back off. Would it hurt to blow some heat in there or just leave it in the baggy? Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now