jester69 Posted August 8, 2014 Report Share Posted August 8, 2014 I've got some scuff marks on my SS bracelet and would like any advice how to buff these to match the rest of the band. Pic below. Note: I'm a machinist and have buffing supplies, but would like specific advice on doing this on a watch bracelet. I'm just worried I'll have to buff the entire thing. I mean is there some magic polish out there that I can hand apply to buff this out? Link to comment Share on other sites More sharing options...
GenTLe Posted August 8, 2014 Report Share Posted August 8, 2014 (edited) See post #7 here: http://www.rwgforum.net/topic/171149-omega-seamaster-po-liquidmetal-from-noob-short-review/?hl=dremel#entry1347803 PS: the sandpaper I use must be dry/wet version and used soaked with water. Edited August 8, 2014 by GenTLe Link to comment Share on other sites More sharing options...
jester69 Posted August 8, 2014 Author Report Share Posted August 8, 2014 Cool. Thanks. Link to comment Share on other sites More sharing options...
kbh Posted August 8, 2014 Report Share Posted August 8, 2014 If you're looking for Rolex style brushed finish, here's what I use. Picked up the tip from a gen watch forum. It's available at Home Depot. Also, the wet or dry sandpaper works fine also. Link to comment Share on other sites More sharing options...
jester69 Posted August 8, 2014 Author Report Share Posted August 8, 2014 Ah good idea. I have lots of grades of steel wool already. Link to comment Share on other sites More sharing options...
Tim Posted October 22, 2014 Report Share Posted October 22, 2014 Scotchbrite pad is a better solution than steel wool or sandpaper. Or use a fiberglass pen. A fiberglass pen is more accurate and you can easily work on a single link with one. Steel wool is usually carbon steel and you generally don't wnat to embed carbon steel particles into stainless steel. Sand paper will leave grit that can hasten the demise of your bracelet. Link to comment Share on other sites More sharing options...
fraggle42 Posted October 22, 2014 Report Share Posted October 22, 2014 Kitchen plastic pan cleaner is what I've used upto now. I found that varying the pressure produces different finishes from very fine grain up to deep medium grain, and it's not that abrasive, so it's a process of "slow and steady" gets there in the end. I would worry about sandpaper being more abrasive than plastic that if I slipped and got one stroke wrong, it would take quite a bit to correct it, but something very light, one wrong slip and it hardly marks it - but of course it does take a lot longer to get the finish required. I also found it is VERY advisable to use a brand new kitchen scrapy sponge every job, then you know exactly what it will do when you start using it, and there's no hard, crusty bits of blackened cooked things stuck in it Link to comment Share on other sites More sharing options...
Tim Posted October 23, 2014 Report Share Posted October 23, 2014 Kitchen plastic pan cleaner is what I've used upto now. I just have one question fraggle42. Has Simon ever named his cat? You're quite right! Unless you're well practiced, slow and steady is the best approach for touching up your case metal. 1 Link to comment Share on other sites More sharing options...
kbh Posted October 23, 2014 Report Share Posted October 23, 2014 If you're looking for Rolex style brushed finish, here's what I use. Picked up the tip from a gen watch forum. It's available at Home Depot. Also, the wet or dry sandpaper works fine also. Don't get the wrong idea.. This isn't steel wool. It's a scotch brite pad the "replaces 0000 steel wool". Read the package again. 1 Link to comment Share on other sites More sharing options...
Tim Posted October 25, 2014 Report Share Posted October 25, 2014 Ah, so it is. Good. Hard to read a photo on a phone sometimes. Link to comment Share on other sites More sharing options...
fraggle42 Posted October 25, 2014 Report Share Posted October 25, 2014 I just have one question fraggle42. Has Simon ever named his cat? . Haha, as far as I know he has never revealed the cats name. Love the cartoons and have a stuffed Simons cat at work Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now