chad Posted September 1, 2009 Report Share Posted September 1, 2009 I have a pair of real great base reps and have owned the gamut of pam reps and gens. I have been wearing my 176g gen for a while and went to the 112 rep today today. I have seen one or two luminor cased reps without this issue but most do. Even the most highly modded. The dial appears sunken too low on the reps. Can this be fixed in anyway? I am talking about a very very small amount but it is noticeable even on the wrist of another person. Here in NYC on the subway I use it to tell pam rep from the person across the car. Anyway, is there a way to raise the dial slightly without too much trouble? Anyone else notice this? Could it be due to the angle the crystal is cut and false magnification? Link to comment Share on other sites More sharing options...
jdkno Posted September 1, 2009 Report Share Posted September 1, 2009 You mean like this? Link to comment Share on other sites More sharing options...
chad Posted September 1, 2009 Author Report Share Posted September 1, 2009 Yea but it is still deeper than my gens. That looks pretty good though as do most of the automatics/chronos (daylights do not have this problem at all) I am speaking more of the handwinds. Chad You mean like this? Link to comment Share on other sites More sharing options...
chad Posted September 1, 2009 Author Report Share Posted September 1, 2009 Take a look down the page at FGD's collection. It is fantastic do not get me wrong, i am just showing the problem extends even to the finest pieces out there. now look at this ad on risti. http://www.network54.com/Forum/611718/thread/1246568373/last-1247506236/Only+for+the+fellow+Risti-+FS-+low+price-+201-A%2C+1BT%2C+25A%2C+127+%28GerardfromHolland%29 The difference is not subtle IMHO, and appears almost twice as deep from some angles. The dial appears to be right up on the crystal at all angles. I say "appears" because I still do not know if the dials need to be moved up or the rep crystals are giving a false optical illusion. Link to comment Share on other sites More sharing options...
StormTooper4 Posted September 2, 2009 Report Share Posted September 2, 2009 Chad if you could post a picture of your offending rehaut then perhaps we could appreciate the issue a bit more. From the my experience, as limited as it may be rehaut is not really an issue with PAM's. But If you can show a picture of your gen vs rep rehauts that would great and I will happily stand corrected. ST4 Link to comment Share on other sites More sharing options...
kye_lin Posted September 2, 2009 Report Share Posted September 2, 2009 I can understand where CHAD is coming from.. if you look at FGD's collection... at certain angles.. the rehaut looks pretty thick... Not sure is it because of that particular angle of shot... OR... are the casesets from DSN?? DSN casesets sometimes have really abnormally tall bezels thus giving the bigger rehaut??? Just a thought.. might be completely wrong here... Cheers.. Link to comment Share on other sites More sharing options...
chad Posted September 2, 2009 Author Report Share Posted September 2, 2009 Sure I will try and post some pics today. The FGD example I gave you is not subtle though. It is far more visible than a flattened CG pin or an "L swiss vs T swiss" or a crown that is .1 mm off in thickness. (i notice those things also) Have you wore a gen for an extended period and then a rep of the same watch? Chad if you could post a picture of your offending rehaut then perhaps we could appreciate the issue a bit more. From the my experience, as limited as it may be rehaut is not really an issue with PAM's. But If you can show a picture of your gen vs rep rehauts that would great and I will happily stand corrected. ST4 Link to comment Share on other sites More sharing options...
chad Posted September 2, 2009 Author Report Share Posted September 2, 2009 i agree about dsn and some strange things going on with certain proportions on his casesets. I can understand where CHAD is coming from.. if you look at FGD's collection... at certain angles.. the rehaut looks pretty thick... Not sure is it because of that particular angle of shot... OR... are the casesets from DSN?? DSN casesets sometimes have really abnormally tall bezels thus giving the bigger rehaut??? Just a thought.. might be completely wrong here... Cheers.. Link to comment Share on other sites More sharing options...
archibald Posted September 3, 2009 Report Share Posted September 3, 2009 I really only notice the rehaut issue in two areas. On handwinds the issue is really only that noticeable IMO on DSN cases which are flawed in numerous other ways--so i just avoid them in general. Comparing a very old school rep 111, a gen 112, a franken 03 w/ a jimmy case, and a gen 118, however, I notice very little difference. The easiest solution seems to be swap your parts to better case if it bothers you. The older rep handwind cases sell for, what, 40 bucks? The other issue is more difficult. I believe that in many instances repmakers maximise the mag of (and/or provide hand clearance for) the thinner bk7 cyclopses they use by increasing the height of the rehaut. Certainly they understand that the reason their cyclopses will never match gen mag since gens use sapphire cyclopses with better focal length. And they also understand that mag increases the farther asway a lens is from whatever it's magnifying. For example, honpo 23 and 27 bezels are 1.5mm thicker than their gen counterparts. My rep ti 89 case also looks like it has a deeper rehaut than gen, (and the gen xtal on it looks like it's a little too powerful for that reason, I bet) but I can't prove it. I used jimmy cases on kruzer's 23 and my 27 frankens with good results but milling of the case is needed obviously. Other than that, I don't know what to do. Link to comment Share on other sites More sharing options...
ubiquitous Posted September 11, 2009 Report Share Posted September 11, 2009 Hmmmm... I think Chad means a shallow rehaut like so? In my opinion, this is also an effect of crystal optics as well. I just recently switched to the sapphire as fitted in the pics above; prior to this, I had a different crystal fitted, and the effect was a taller rehaut: Link to comment Share on other sites More sharing options...
redwatch Posted September 11, 2009 Report Share Posted September 11, 2009 Wow R that's the same watch? What an amazing difference between the two different crystals! It seems like a totally different build from the photos! Link to comment Share on other sites More sharing options...
ubiquitous Posted September 12, 2009 Report Share Posted September 12, 2009 Yessir- Same Jimmy case and set up in the pics; only difference is the crystal. The new sapphire is an old rep crystal I had in the parts bin; I stripped off the lite AR, and pressed it in. Looks pretty decent, though I'm going to give the inner surface another polish. Interesting to see the changes a crystal can make... Link to comment Share on other sites More sharing options...
kbiz Posted September 12, 2009 Report Share Posted September 12, 2009 The affect is the definitely the refraction of light through the crystal... in the Gen pics it appears the rehaut is thinner than is possible to clear the hand stack, which is obviously impossible. The thickness of the crystal and the index of refraction of the crystal are at play here... the rep crystal will not have the same index of refraction because it isn't the same type of sapphire... so the thickness has to be adjusted. I'd say try a couple different crystals... the one's they sell on ebay are very thick... just a thought. Link to comment Share on other sites More sharing options...
projectologist Posted September 12, 2009 Report Share Posted September 12, 2009 Yea but it is still deeper than my gens. That looks pretty good though as do most of the automatics/chronos (daylights do not have this problem at all) I am speaking more of the handwinds. Chad The pic jdkno posted (post #2) is of a gen 88. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now