nagyr Posted January 26, 2010 Report Share Posted January 26, 2010 (edited) How is it possible to remove the stem from this movement? (would like to remove the whole movement) Thanks, R Edited January 26, 2010 by nagyr Link to comment Share on other sites More sharing options...
FxrAndy Posted January 26, 2010 Report Share Posted January 26, 2010 See attached picture Link to comment Share on other sites More sharing options...
marinamm20 Posted January 26, 2010 Report Share Posted January 26, 2010 just press the small "dot" right under to the right of the stem and pull out arrgh FxrAndy you was faster on the draw Link to comment Share on other sites More sharing options...
FxrAndy Posted January 26, 2010 Report Share Posted January 26, 2010 Link to comment Share on other sites More sharing options...
Toadtorrent Posted January 26, 2010 Report Share Posted January 26, 2010 Hah hah...nice responses...Andy's guns are SMOKIN'... Link to comment Share on other sites More sharing options...
marinamm20 Posted January 26, 2010 Report Share Posted January 26, 2010 RIP Link to comment Share on other sites More sharing options...
nagyr Posted January 26, 2010 Author Report Share Posted January 26, 2010 Perfect. Thank you! Link to comment Share on other sites More sharing options...
Prsist Posted December 30, 2010 Report Share Posted December 30, 2010 Resurrecting the old thread. Is a stem swap this simple? I have a PT 1665 with a 2846 movt. Just want to make sure it is as easy as it looks. Link to comment Share on other sites More sharing options...
FxrAndy Posted December 30, 2010 Report Share Posted December 30, 2010 on a 2846 make sure you remove the stem in the hand set position, why would you just want to swap the stem? Link to comment Share on other sites More sharing options...
Prsist Posted December 30, 2010 Report Share Posted December 30, 2010 on a 2846 make sure you remove the stem in the hand set position, why would you just want to swap the stem? Andy, forgive me. i meant to say Crown swap. A few beers at dinner, a few more surfing the net and my brain is scrambled. I have a gen crown id like to put on myself. Link to comment Share on other sites More sharing options...
FxrAndy Posted December 30, 2010 Report Share Posted December 30, 2010 Ah ok does the tub on them take a gen crown, if so that is good news Link to comment Share on other sites More sharing options...
Prsist Posted December 30, 2010 Report Share Posted December 30, 2010 Ah ok does the tub on them take a gen crown, if so that is good news I have been told they do. I guess we will soon see. Link to comment Share on other sites More sharing options...
FxrAndy Posted December 30, 2010 Report Share Posted December 30, 2010 I think i have read that somewhere as well, keep us posted and let us know for sure please Link to comment Share on other sites More sharing options...
Prsist Posted December 30, 2010 Report Share Posted December 30, 2010 I think i have read that somewhere as well, keep us posted and let us know for sure please The above tutorial shows how to remove the stem, but how do you swap the Crown? Link to comment Share on other sites More sharing options...
Dizzy Posted January 2, 2011 Report Share Posted January 2, 2011 Gen crown fit on my PT 1680 but not sure if its water resistant or not. I always release the stem in the winding position on all my watches. Ive heard people argue both ways, but so far I havent had any problems. Be sure to use nothing but a 1.2mm screwdriver on that ETA to remove the stem. The keyless works are EASILY wrecked by pushing that little button in too far. AFter removing, I measure from the end of the stem to the base of the crown with calipers to get the length. Then I hold the stem with some needle nose plyers and carefully unscrew the crown from the stem. Then you just screw on the Rolex crown. Be sure to make the length the SAME as it was before. You may need to use a half drop of GS hypo or locktight to hold the stem secure at the right length. Then carefully reinsert the stem turning it slightly to "wiggle" it in if needed. Its pretty easy to do. Link to comment Share on other sites More sharing options...
FxrAndy Posted January 2, 2011 Report Share Posted January 2, 2011 Hmm i always release in the hand set position, i have had problems doing it in the winding pos so after another course and finding out the ETA way is to do it in the hand set position i have not had a problem since. Link to comment Share on other sites More sharing options...
Prsist Posted January 3, 2011 Report Share Posted January 3, 2011 Hmmmmm. I just took the stem/crown out. I measured, and took the crown off and put the new crown on, measured again and reinstalled the stem/crown. I can: 1. adjust the date 2. adjust the time 3. wind the movement I cannot screw the crown back into the watch. Anyone have an idea where I went wrong? Side note: I read how the gen crown is smaller than the rep but I didn't notice much difference. EDIT: > 5 minutes later after playing around with the crown I was able to screw the crown back to "wearable state". One problem, I turned the crown maybe, maybe 2-3mm. Not the normal turns as you would expect. > I am thinking I screwed the crown onto the stem a little too far. What do the pros think? Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now