FDG Posted June 19, 2010 Report Share Posted June 19, 2010 One of my first reps, a Omega PO. Which I bought from someone just because I liked the watch. He sold it to me as a ETA version (clueless what that meant at that time). And without knowing much of rep watches, I just went diving with it, up till 40 meters deep, no problems at all. Was I just lucky? Link to comment Share on other sites More sharing options...
UT Horn Posted June 20, 2010 Report Share Posted June 20, 2010 Well, after day 2 in the pool and going down to 8' the watch failed. The crystal was fogged up this morning. I've opened the crown in hope it will dry out. So much for testing out @ 3 bars! Anyone think this watch will survive as is? Link to comment Share on other sites More sharing options...
FxrAndy Posted June 20, 2010 Author Report Share Posted June 20, 2010 Find some silica gel packs like you get in new shoes ans electrical items, and a small tuperware container or a zip lock bag remove the case back and get it all sealed op to get the moisture out asap then there is a good chance it will survive Link to comment Share on other sites More sharing options...
UT Horn Posted June 20, 2010 Report Share Posted June 20, 2010 Andy, Thanks for the quick reply! I found one pack and am hoping it works. I don't see any water in the watch, so I may be in luck. Worst part is I was expecting my watch to be waterproof enough for my pool as I plan on wearing it in there regularly. Chris Link to comment Share on other sites More sharing options...
FxrAndy Posted June 20, 2010 Author Report Share Posted June 20, 2010 I collect all the silica gel packs i find and store them in an airtight box to use as a dry room in case of things like this Link to comment Share on other sites More sharing options...
UT Horn Posted June 20, 2010 Report Share Posted June 20, 2010 Smart man. I'll be doing the same. Btw, I found 2 more. Link to comment Share on other sites More sharing options...
Stephane Posted June 21, 2010 Report Share Posted June 21, 2010 I build a 1665 MBW for Saso in the past,he tested it on a local watchsmith up to 300m..... Well that is why I can wash the dishes with my great white then Link to comment Share on other sites More sharing options...
UT Horn Posted June 21, 2010 Report Share Posted June 21, 2010 Andy, Your trick appears to have worked for my watch. At this time it's running smoothly and there is no moisture in the watch anymore. Thanks for the help! Now to figure out what went wrong... Link to comment Share on other sites More sharing options...
panerai153 Posted June 21, 2010 Report Share Posted June 21, 2010 Andy, Your trick appears to have worked for my watch. At this time it's running smoothly and there is no moisture in the watch anymore. Thanks for the help! Now to figure out what went wrong... UT, there have been many posts about water resistance on the forums over the years. The general consensus is that you should treat every rep watch as being non water resistant until proven otherwise. The QC as we all know is non existant with reps, despite what some sellers tell you, excetions would be BK and possibly WM9. Other than those, I would have the watch pressure tested and see if it holds up. If the tolerences are within spec, gaskets and o rings are siliconed, then it should be Ok, but without a pressure test, you are taking a real chance submersing a rep. You were lucky, yours was probably a tiny leak and it was in fresh water. Get a seawater flood, and your new watch is an expensive paperweight! Best to be safe than sorry. Link to comment Share on other sites More sharing options...
UT Horn Posted June 21, 2010 Report Share Posted June 21, 2010 UT, there have been many posts about water resistance on the forums over the years. The general consensus is that you should treat every rep watch as being non water resistant until proven otherwise. The QC as we all know is non existant with reps, despite what some sellers tell you, excetions would be BK and possibly WM9. Other than those, I would have the watch pressure tested and see if it holds up. If the tolerences are within spec, gaskets and o rings are siliconed, then it should be Ok, but without a pressure test, you are taking a real chance submersing a rep. You were lucky, yours was probably a tiny leak and it was in fresh water. Get a seawater flood, and your new watch is an expensive paperweight! Best to be safe than sorry. I hear what you are saying, but I paid extra $ to have the watch gaskets siliconed and to have the watch tested for waterproofness. I was told it tested ok to 3 bars. I bought the watch from Narikka and he's always shot straight with me, so I assumed the information was good. I now need to get the watch looked over by someone local to ensure this doesn't happen again. Link to comment Share on other sites More sharing options...
panerai153 Posted June 22, 2010 Report Share Posted June 22, 2010 I think that's the wise thing to do. Take it to a local watchmaker that has a pressure tester. that way you can see whats happening and possibly see where the water ingress point is. If you see it with your own eyes and are confident that it's tight, then you can head for the pool again. Pretty silly that the reps of today, especially those that are top grade (300-600 dollars aren't water resistant. there are lots and lots of genuine watches in that price range that are water tight, why can't the reps be as well. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now