trueimage Posted May 29, 2007 Report Share Posted May 29, 2007 On what I need and how to adjust the strap on my new UPO? I can fit 2 fingers wide by 1 finger tall under the strap when it is on my wrist where I want to wear it. Help! Thanks. Link to comment Share on other sites More sharing options...
b16a2 Posted May 29, 2007 Report Share Posted May 29, 2007 These are notoriously tricky to remove, I would recommend taking it to a local watchmaker to remove for you. Most watches with pins in the links can be removed using a link remover tool that you can usually pick up on eb@y. Link to comment Share on other sites More sharing options...
NaviChief Posted May 29, 2007 Report Share Posted May 29, 2007 These are notoriously tricky to remove, I would recommend taking it to a local watchmaker to remove for you. Most watches with pins in the links can be removed using a link remover tool that you can usually pick up on eb@y. The PO bracelet snapped my eBay link remover clear in two! The bracet is evil I tell you..... Link to comment Share on other sites More sharing options...
Stephane Posted May 29, 2007 Report Share Posted May 29, 2007 The plastic pin link removers from eBay are indeed too fragile. Here is what I finally used myself (A FlipTopBuckle Hammer) Link to comment Share on other sites More sharing options...
Usil Posted May 29, 2007 Report Share Posted May 29, 2007 I have done three UPO's and used the method below without issues. You will need several tools. Removing: 1. A pin removal tool that has a thick pin. This is needed to start the pin out of the bracelet so that the removal pin does not bend in the process. 2. The pin tool above will only get it out about half way so you will need another pin tool with a longer pin to get it out a little further. You need to get it out at least 3/4 of the way to start using pliars (carefully) to remove it the rest of the way. 3. Using pliars, pull straight out. If it is not already at least 3/4 the way out it is very likly you will break the pin. Replacing: 1. Align the bracelet and using pliars, start the end of the pin a little into the bracelet. Make sure you use some oil on the pin before inserting into the bracelet. Slowly, push straight. It should go in at least 1/4 to 1/2 way. From here on it is impossible to get any further unless you use a small jewlers/watch hammer to lightly and repetatively tap the end of the pin the rest of the way in. You must do this a little at a time and make sure you tap exactly vertically so as not to bend the pin. The plastic end of the hammer can be used at the start but you will probably find that the end of the pin start to embed into the resin and you will have to change to the metal end of the hammer as it gets harder to move the pin. A note on the pliars. Use carefully so as not to scar or bend the pin. I used a pair that had flat on the end with no teeth. This is the procedeure I used on all three UPO's and it worked each time. But, you have to have the tools and don't even start to do this unless you do. Good luck. You will need it. Usil Link to comment Share on other sites More sharing options...
Pugwash Posted May 29, 2007 Report Share Posted May 29, 2007 PO pins also have a sleeve in each link that the pin slots into. Don't lose these. Edit: Here's a picture of the three components of each link: Link to comment Share on other sites More sharing options...
trueimage Posted May 29, 2007 Author Report Share Posted May 29, 2007 I have done three UPO's and used the method below without issues. You will need several tools. Removing: 1. A pin removal tool that has a thick pin. This is needed to start the pin out of the bracelet so that the removal pin does not bend in the process. 2. The pin tool above will only get it out about half way so you will need another pin tool with a longer pin to get it out a little further. You need to get it out at least 3/4 of the way to start using pliars (carefully) to remove it the rest of the way. 3. Using pliars, pull straight out. If it is not already at least 3/4 the way out it is very likly you will break the pin. Replacing: 1. Align the bracelet and using pliars, start the end of the pin a little into the bracelet. Make sure you use some oil on the pin before inserting into the bracelet. Slowly, push straight. It should go in at least 1/4 to 1/2 way. From here on it is impossible to get any further unless you use a small jewlers/watch hammer to lightly and repetatively tap the end of the pin the rest of the way in. You must do this a little at a time and make sure you tap exactly vertically so as not to bend the pin. The plastic end of the hammer can be used at the start but you will probably find that the end of the pin start to embed into the resin and you will have to change to the metal end of the hammer as it gets harder to move the pin. A note on the pliars. Use carefully so as not to scar or bend the pin. I used a pair that had flat on the end with no teeth. This is the procedeure I used on all three UPO's and it worked each time. But, you have to have the tools and don't even start to do this unless you do. Good luck. You will need it. Usil Sounds.... great. About taking it to a jewelery store: Will they do it while I'm there / let me watch or must I leave the watch. Also, they used to sell Omega and now they do not, but they still sell Tag Heuer I think is their top brand. Will they deny me service if they spot this as a "fake". Lastly, what is the average charge for this service. I think I'd like to have the tools on hand for the future with other watches etc, but I want it done right away. Link to comment Share on other sites More sharing options...
Usil Posted May 29, 2007 Report Share Posted May 29, 2007 First, before handing over a rep (make sure this is not an authorized dealer), ALWAYS ask if they have an issue with working on reps. If they say no or ask what you want done just say that you need the bracelet resized and have been told it is a difficult one because of the tight pins. Do this on the phone. If they say - sure bring it is then you got it made. Keep calling till you find one. A small independant is best. I have no idea on the charge - you will have to ask them. Tools to do this are not too expensive if you plan to get more reps then you will need them. Uisl Link to comment Share on other sites More sharing options...
trueimage Posted May 29, 2007 Author Report Share Posted May 29, 2007 Thanks for the tip. I live in a remote location so there are only a few places. I will call around and see. Can you recommend what to get / where to get a "starter" kit for watch repair/work? Just like the tool to remove caseback and the small screwdrivers (i.e. for adjusting the time offset) and working on bracelets, etc. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now