TeeJay Posted August 31, 2007 Report Share Posted August 31, 2007 (edited) My GMT Submariner project... The parts arrived today, and, thanks to a set of rubber gloves, I was able to open the casebacks. Stripped out the movements and set about swapping the dials... The Sub dial's center hole wasn't wide enough to go over the extra width for the GMT movement, so I got a round file, and started twisting... I got a bit carried away and the hole wound up too large. Scrapped it. I then remembered the spare vintage dial I have from the Silix Rolex, so same procedure, stripped it and gently enlarged the hole, and, removing the locating pins, the dial went over perfectly. A tiny dab of superglue fixed the dial in place, the hands went back on flawlessly, so it was time to replace the movement in the case. This was where things really went wrong, as the crown wouldn't properly engage. The movement had worked after the hands and dial were replaced, so I know there wasn't any glue seeped into the movement, so I'm guessing something's fouled up the keyless works (if that's the right part) and it just won't engage the crown. Oh well, both watches were Edited August 31, 2007 by TeeJay Link to comment Share on other sites More sharing options...
FxrAndy Posted August 31, 2007 Report Share Posted August 31, 2007 It is the best way to learn TJ Link to comment Share on other sites More sharing options...
TeeJay Posted August 31, 2007 Author Report Share Posted August 31, 2007 It is the best way to learn TJ Indeed, I'm not too concerned, as I'm getting a new vintage dial from Silix for the vintage Submariner, and I can always order another Submariner and GMT Master II and try again. Oh, I forgot to say, by putting the dateless dial in the GMT case, I had to remove the cyclops, and, a cigar lighter (aka mini blowtorch) did that effortlessly Link to comment Share on other sites More sharing options...
TeeJay Posted August 31, 2007 Author Report Share Posted August 31, 2007 So I decided to have another look at the watch, and I noticed that a piece of metal just beneath where the crown stem enters the movement had slipped down, so, a flick of a craft knife to put it back into place, and, the movement then engaged the stem IT'S ALIVE!!!!! Pics of the watch to follow in due time Link to comment Share on other sites More sharing options...
Slartibartfast Posted August 31, 2007 Report Share Posted August 31, 2007 Pics of the watch to follow in due time Cant wait .. sounds interesting. I am really tempted to give this modding lark a try. Link to comment Share on other sites More sharing options...
FxrAndy Posted August 31, 2007 Report Share Posted August 31, 2007 great news TJ, so the whole project cost you what Link to comment Share on other sites More sharing options...
TeeJay Posted August 31, 2007 Author Report Share Posted August 31, 2007 Cant wait .. sounds interesting. I am really tempted to give this modding lark a try. It's something I've had in mind for several months, but always had 'more important' watches to buy before getting into it. The result isn't entirely as planned, as I wanted a contemporary Submariner dial in the GMT case, but wound up having to use the vintage Submariner dial... Oh well, it'll suffice untill I can order more parts in to try again great news TJ, so the whole project cost you what Link to comment Share on other sites More sharing options...
FxrAndy Posted August 31, 2007 Report Share Posted August 31, 2007 Are you using the correct crown stem, ie were the stems the same for both watches, have you got the GMT one in the GMT works and the sub one in the sub works? Link to comment Share on other sites More sharing options...
TeeJay Posted August 31, 2007 Author Report Share Posted August 31, 2007 Are you using the correct crown stem, ie were the stems the same for both watches, have you got the GMT one in the GMT works and the sub one in the sub works? Yes, I was careful not to mix the parts like that The stem for the sub actually broke off going back in, so has totally fouled that movement, but for Link to comment Share on other sites More sharing options...
FxrAndy Posted August 31, 2007 Report Share Posted August 31, 2007 Another q does the movement stop at a particular point every time or area on the dial? i dont mean catching just stopping particualy around 9 Link to comment Share on other sites More sharing options...
TeeJay Posted August 31, 2007 Author Report Share Posted August 31, 2007 Another q does the movement stop at a particular point every time or area on the dial? i dont mean catching just stopping particualy around 9 I think I've solved the problem. The 'back' of the second hand had gotten slightly bent down, and had been catching against the minute hand. I stripped the watch, tweaked the hand, and it seems to have done the trick Link to comment Share on other sites More sharing options...
FxrAndy Posted August 31, 2007 Report Share Posted August 31, 2007 good good, how is the winding now? Link to comment Share on other sites More sharing options...
TeeJay Posted August 31, 2007 Author Report Share Posted August 31, 2007 good good, how is the winding now? Still not perfect, but it's not stopping, so at I suspect that was a jam rather than a problem with the movement 'losing power'. Here're a couple of pictures of it Link to comment Share on other sites More sharing options...
FxrAndy Posted August 31, 2007 Report Share Posted August 31, 2007 Hmmmmm interesting. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now