SWATCHman Posted December 12, 2007 Report Share Posted December 12, 2007 (edited) This mod is extremely simple, effective and very durable: I read about different methods of modding the PAM lever in order to make it nice and tight. There are two techniques around. One requires cable insulation to fill the gap between pin and lever, another one employs silicone for the same purpose. The more sophisticated solution is the cable insulation, the quick fix is the Silicone variant. I did not have cable in the right diameter and I was not to crazy about the silicone option either. So while agreeing on the general principle of filling the space around the pin to tightn it, I did not like the means. So based on the general idea of the existing techniques I thought about alternatives that do not require materials with a certain diameterrequire as little fumbling around witht the lever pin as possible in order to keep it from disappearing don't require any wait (like the Silicone overnight option), cutting down on time in which screw an pin can get lostis very easy to apply and does not require special skillscan easily renewed after wear and tear has loosened the lever again hot glue adhesive, which is readily available in most households. Tools required:a pistol for hot glue adhesivea screw driver to loosen the crown screwsa pin removal tool or small drilla small hammer Step one: Fire up the glue pistol. Step two: Detach crownguard from your pam and safely store the screws away. Step three: Put the crownguard bottom up on a piece of soft wood. Use the pin removal tool or small drill to dislodge the pin from the crownguard. Be careful not to loose it once you pushed it out. The result should look like this. Step four: Place the lever on a table. The hole for the pin needs to be vertical. Then place the tip of the glue pistol on top of the lever without squeezing out any glue. Now the lever is slowly heated up by the glue pistol. Step five: Once the lever is really hot apply glue to the pin hole in the lever until it comes out on the opposite side of the lever. Then let the lever cool for 5 minutes. Step six: Remove excess glue, your fingernails should do the trick. Step seven Place the lever back in the crown guard and reinsert the pin just a tiny bit (1mm). Step eight: Put the glue pistol on top of the pin and wait until it picks up the heat. After a while, it will just sink into the crownguard until it is all the way through the lever. Stop pushing when the pin is still sticking out 2mm. Step nine (optional): If you want the pin to sit flush with the surface of the crownguard, now is a good moment to file or sand the top of the pin to a smooth flat finish. Flat surface after filing and sanding. Step ten: Place the tip of the glue pistol over the pin and heat up both pin and crownguard. This takes a couple of minutes. Step eleven: Gently push the pin down. If you want it to sit flush with the surface a hard piece of wood will do. If the pin is supposed to be sunken, the pin removal tool or small drill will do. Step twelve: Remove excess glue with your fingernails or with some solvent. Step thirteen: Re-attach the crownguard to the watch and enjoy the great new experience of opening and closing a tight lever. And now the best thing for last. Should the lever ever become loose again (the glue will definitely outlast any silicone though), just use the glue gun again to reheat the lever. You don't even need to disassemble the crownguard this time around. Just press the pistol on the crownguard for 2 minutes. The glue will melt again and settle tightly around the pin. Once it has cooled off, you're good to go for another couple of months. You can repeat this indefinitely, one application should last the lifetime of the watch. . Edited December 12, 2007 by SWATCHman Link to comment Share on other sites More sharing options...
mikellem Posted December 13, 2007 Report Share Posted December 13, 2007 Excellent alternative! I like it.. Great photography, thanks for sharing. -MM Link to comment Share on other sites More sharing options...
deltatahoe Posted December 13, 2007 Report Share Posted December 13, 2007 great review SWATCHman -- top quality stuff. thanks so much for taking the time to put it together deltatahoe Link to comment Share on other sites More sharing options...
Bazz Posted December 13, 2007 Report Share Posted December 13, 2007 Great post Thanks for taking the time to put it together as I am sure it took a while to do :smile: Link to comment Share on other sites More sharing options...
Dani Posted December 13, 2007 Report Share Posted December 13, 2007 Very nice and useful post Thanks. Link to comment Share on other sites More sharing options...
HauteHippie Posted December 13, 2007 Report Share Posted December 13, 2007 A great idea and interesting alternative to small surgical tubing! Link to comment Share on other sites More sharing options...
a german in denmark Posted December 13, 2007 Report Share Posted December 13, 2007 Great stuff SWATCHman, thanks a lot Link to comment Share on other sites More sharing options...
DuDro Posted December 13, 2007 Report Share Posted December 13, 2007 Off to Michael's Arts & Crafts to buy a hot glue gun...Thanks! Link to comment Share on other sites More sharing options...
tech Posted December 13, 2007 Report Share Posted December 13, 2007 Thanks for taking the time and putting this together! Post of the month award......hmmmmmm Link to comment Share on other sites More sharing options...
phaedo Posted December 13, 2007 Report Share Posted December 13, 2007 Time to buy a hot glue gun I think... This should also work on CG's that are so floppy they don't actually stay closed too, right? Link to comment Share on other sites More sharing options...
SWATCHman Posted December 13, 2007 Author Report Share Posted December 13, 2007 (edited) Time to buy a hot glue gun I think... This should also work on CG's that are so floppy they don't actually stay closed too, right? Yes it does. My lever was totally too loose. It was just flopping around. Now it stays in any position I leave it. Did the same md to my 111H. Had to hold it by the lever when sanding and filing crown guard an pin into the right shape. Still nice and tight, so far no wear at all. And even if it wears out after some time, reheat it and it will be like new... Edited December 13, 2007 by SWATCHman Link to comment Share on other sites More sharing options...
deniz21 Posted December 13, 2009 Report Share Posted December 13, 2009 dam im too late the pics are gone, but respect for sure a great post,or are the other ways better?? greetings deniz Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now