jake48 Posted July 22, 2008 Report Share Posted July 22, 2008 Well - I knew better... Two of my friends had the new GMT II ceramic with the uneven crystal - low on the 9 O'clock side and so did I. They fixed theirs by pressing the crystal "as is" and were able to make it level. I told them (being the ever so cautious one) that the correct way to do it was to remove the crystal, check the gasket for slippage and then reassemble the crystal to press it on "correctly" After reading a few more successful reports here on RWG of people pressing their crystals straight I decided to go against my own advice and press away... This is the before: This is the after: I set the press up to apply more pressure on the high side (3 O'clock side) and I am sure this is what caused it (uneven pressure on the crystal) All I can say if you don't take the crystal out and repress it evenly is - DO YOU FEEL LUCKY? And I knew it was bound to happen- God, I am a moron some time... Link to comment Share on other sites More sharing options...
LegendofSpeed Posted July 22, 2008 Report Share Posted July 22, 2008 nooooooooooooooooooooooooooooooooo!!!!!!!!!!!!!! Link to comment Share on other sites More sharing options...
jake48 Posted July 22, 2008 Author Report Share Posted July 22, 2008 nooooooooooooooooooooooooooooooooo!!!!!!!!!!!!!! Yeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeess!!!!!!!!!!!!!! Link to comment Share on other sites More sharing options...
Steve G Posted July 22, 2008 Report Share Posted July 22, 2008 I just saw this on the other board and like a bad car accident I cannot look away. I say again ouch Link to comment Share on other sites More sharing options...
mikellem Posted July 22, 2008 Report Share Posted July 22, 2008 I give you credit for trying... The only way to learn... Better luck.. Link to comment Share on other sites More sharing options...
freddy333 Posted July 22, 2008 Report Share Posted July 22, 2008 Ouch. All is not lost though. You can purchase another aftermarket sapphire crystal & gasket for $40. There are probably others available, but you will have to do the searching. The 1 I listed should work though. Link to comment Share on other sites More sharing options...
jake48 Posted July 22, 2008 Author Report Share Posted July 22, 2008 Ouch. All is not lost though. You can purchase another aftermarket sapphire crystal & gasket for $40. There are probably others available, but you will have to do the searching. The 1 I listed should work though. freddy - I am in for the Lani/Chief Ar cyclops and was wondering... Would the crystals Lani is taking the cyclops off of work as a possible replacement? I am not familiar with the different sized crystals that are same for different Rolex models, but one thing that concerns me, other than the obvious crystal dimensions, is the bevel on the crystal. Is the datejust crystal that you listed the same as a GMT? Link to comment Share on other sites More sharing options...
StormTooper4 Posted July 22, 2008 Report Share Posted July 22, 2008 OH SH!T Dude good luck with the repalcement ST4 Link to comment Share on other sites More sharing options...
freddy333 Posted July 22, 2008 Report Share Posted July 22, 2008 freddy - I am in for the Lani/Chief Ar cyclops and was wondering... Would the crystals Lani is taking the cyclops off of work as a possible replacement? I am not familiar with the different sized crystals that are same for different Rolex models, but one thing that concerns me, other than the obvious crystal dimensions, is the bevel on the crystal. Is the datejust crystal that you listed the same as a GMT? I cannot remember which crystal model Lani ordered (we were concerning with the cyclops only), so you might check with him. And, not to be negative, but Lani's source for the crystal is not a reliable seller (I am being kind). The crystal I linked should fit most modern Rolex models, including the GMTII. But you might check with the seller to be sure. Otherwise, search ebay for another crystal. There are many of them on the bay. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now