Mrkampa Posted October 27, 2009 Report Share Posted October 27, 2009 Ok so i have an ingy with the ETA 2824-2 movement, i removed the stem when i was sealing up the gaskets and now i cant seem to get the stem to sit back in! Its like the "stem-lock" is open all the time, it dossent "click" when i pres the stem back in. Annyone got some tips on how i can get the stem back in place? -kampa Link to comment Share on other sites More sharing options...
Toadtorrent Posted October 27, 2009 Report Share Posted October 27, 2009 EDITED: I usually press the stem release button to put the stem back in on the 2824 / 2836. If you pushed too hard on insertion/removal, you may have buggered the keyless works and this can't be fixed without taking the dial off. Link to comment Share on other sites More sharing options...
Demsey Posted October 27, 2009 Report Share Posted October 27, 2009 If you pushed too hard, you may have buggered the keyless works and this can't be fixed without taking the dial off. Oh. Cruel fate. What 'tool' did you use to depress the stem release Mk? Please do not tell us it were a 'pin' or similar. Link to comment Share on other sites More sharing options...
FxrAndy Posted October 27, 2009 Report Share Posted October 27, 2009 The stem release pin has a slot above it as a hint to only use a screw driver that size so that you cant depress to far, it sounds like you have depressed to far and the keyless needs re-assembaling Link to comment Share on other sites More sharing options...
Mrkampa Posted October 27, 2009 Author Report Share Posted October 27, 2009 I did use a very small screwdriver. It could be true that i have pressed it to hard. Is there any torturial on how to do this? the reasembly? Link to comment Share on other sites More sharing options...
Francisco Posted October 27, 2009 Report Share Posted October 27, 2009 I did use a very small screwdriver. It could be true that i have pressed it to hard. Is there any torturial on how to do this? the reasembly? for ETA 2824 and 2836 you do not have to push the button to re-install the stem. If so, you will mesh the keyless work. To solve that problem you have to remove hands, dial and the to re-assembly the keyless work. It is an easy fix...the third time you have done it. Regards, Francisco Link to comment Share on other sites More sharing options...
Mrkampa Posted October 27, 2009 Author Report Share Posted October 27, 2009 Sounds like an fun experience! But inorder to get the experience i need some pointers on how to re-assembly the keyless work:) Annyone want to direct me in the right direction? Thanks for all help guy`s! Link to comment Share on other sites More sharing options...
FxrAndy Posted October 27, 2009 Report Share Posted October 27, 2009 there is a tutorial here some where, some one found it just the other week with a similar problem so if you search it should not be to far down Link to comment Share on other sites More sharing options...
FxrAndy Posted October 27, 2009 Report Share Posted October 27, 2009 there is a tutorial here some where, some one found it just the other week with a similar problem so if you search it should not be to far down Link to comment Share on other sites More sharing options...
Toadtorrent Posted October 28, 2009 Report Share Posted October 28, 2009 Keyless Works #1 Keyless Works and Stem Position Reference #2 Keyless Works #3 Keyless Works #4 Link to comment Share on other sites More sharing options...
Demsey Posted October 28, 2009 Report Share Posted October 28, 2009 Good work Tt, I went on a little 'search' myself but came up dry. The new 'Search' function really needs to be used in it's 'expanded' form to get anywhere. MmmK hopefully MrK will see this and have a go.............the tutoral from 'Bazz' is really worth saving to 'Favorites'. Also, the link to 'bigredjoe69' 's tutoral was a hoot; ok many know me by now and know i type as i speak , plain english It may be plain, but I certainly wouldn't call it anything close to 'English'. Plain 'Merican will do. Having sequestered myself on the old RWG when this board was born I completely missed Joe's falling from grace. Pity. He was well revered when they all went over the side, then a pariah. It wasn't until a member returned to the old RWG and clued me in as to why. It's just sad, the dynamic of these forums sometimes. We all tout our 'closeness' in a purported 'brotherhood', but the medium is so detached from anything coming even close to 'human' that one false turn, one misunderstanding, one show of actually being human and the deal goes down the drain. It happens so often as to be remarkable. This strap was a gift from Joe. For no apparant reason other than he thought I should just have it. The bastard. Joe's downfall? Many have their theories and reasons, but I'd put up dollars to dimes it had a lot to do with the last pic in his tutoral. Red neck's should not work on watches. Link to comment Share on other sites More sharing options...
Toadtorrent Posted October 28, 2009 Report Share Posted October 28, 2009 Good work Tt, I went on a little 'search' myself but came up dry. The new 'Search' function really needs to be used in it's 'expanded' form to get anywhere. It only had a LITTLE to do with searching. I had actually saved these threads as PDF's on my computer...and was able to look them up by specific quotes and author name in the search engine. I tried with the regular searching and came up dry as 25 rubies in a Chinese movement. Link to comment Share on other sites More sharing options...
sander Posted October 28, 2009 Report Share Posted October 28, 2009 I tried with the regular searching and came up dry as 25 rubies in a Chinese movement. Link to comment Share on other sites More sharing options...
Mrkampa Posted October 28, 2009 Author Report Share Posted October 28, 2009 Ok, so i did the keyless works, and all looks fine. nothing was out of place in my opinion, then reasembly the watch, and still the stem wont sit! how can this be? Link to comment Share on other sites More sharing options...
Toadtorrent Posted October 28, 2009 Report Share Posted October 28, 2009 Out of my league....sorry. Link to comment Share on other sites More sharing options...
Francisco Posted October 28, 2009 Report Share Posted October 28, 2009 Ok, so i did the keyless works, and all looks fine. nothing was out of place in my opinion, then reasembly the watch, and still the stem wont sit! how can this be? did you press the button when re-installing the stem? In these movement you never have to do it. Regards, Francisco Link to comment Share on other sites More sharing options...
Demsey Posted October 28, 2009 Report Share Posted October 28, 2009 Through my 'Search'-ing yesterday I came across two pieces of obscure info with regard; One countered what 'Francisco' had to add; that depressing the 'stem-release' button, while perhaps not essential, was the course to take when reinstalling the stem (this is my experience as well), and another member suggested rotating the stem clockwise slowly while simultaneously inserting the stem. I did a tutoral for dummies with regard on the old RWG, both of which are lost in the annals, but, it was explained to me that the position of the stem, how it is aligned in rotation upon removal, must be the same at the point of reassembly. I would observe the 'flats' of the stem, and orient them; one parallel to the top of the movement and one parallel the bottom, then removed the stem. If you made no note of their relative position when you removed the stem, then yes, rotating the stem while re-inserting, the flats would, may, find 'home'. The other, as it were explained to me, was the stem needed to be removed in the 'hack' position. It always worked. That aspect has been deliberated ad nauseum. The premier watchsmith here maintains that he always removes the stem from the winding position with every mechanical movement save one Russian made. Just curious, at which detent (stem position) was your crown when you released the stem? Link to comment Share on other sites More sharing options...
freddy333 Posted October 28, 2009 Report Share Posted October 28, 2009 Ok, so i did the keyless works, and all looks fine. nothing was out of place in my opinion, then reasembly the watch, and still the stem wont sit! how can this be? You obviously missed something or put something together wrong. After reassembling the keyless works (but before replacing the dial), insert the stem (without pressing the release pin) & make sure the clutch lever is sitting in the channel on the clutch gear & that the plate adjacent to it is installed correctly (if either is mis-aligned, the stem will not lock in place) (This is an Asian 7750, but the keyless works in most ETAs -- Swiss & Asian -- are similar) If it is, with the stem in the winding position, try to wind the watch. If that works, pull the stem out to the time-setting position & try to set the time. If that works, pull the stem out to the date-setting position & try to set the date. Once you are sure everything is working, return the stem to the winding position, remove the stem & reassemble the watch. Link to comment Share on other sites More sharing options...
Toadtorrent Posted October 28, 2009 Report Share Posted October 28, 2009 Great illustration Freddy. Link to comment Share on other sites More sharing options...
fijikid Posted October 29, 2009 Report Share Posted October 29, 2009 Wow. Been needing this post (and all the tutorials) for years. I almost 100% of the time, have buggered the keyless works when re-installing a stem on an ETA movement. Never had a problem with Seiko movements..hmmm. Anyway, I usually brought them to my chinatown watchman (mr. Lee) and he sorts it for $30. I always thought he was doing me a solid - now I know how relatively easy it is (especially for an experienced watchmaker). Anyway, used Bazz' awesome tutorials and had no problems...well I had one problem. When I 'fixed' it the first time, once I recased the movement the stem wouldn't go in again. Damn. I also remembered that when I test fit the stem prior to re-casing to test everything, the movement wouldn't hand wind. I looked up whether a 2846 should hand wind and found out that it should. Took it all apart again and consulted one of the other tutorials that astutely pointed out that you need to put the U shaped spring on the end of the keyless works cover back in it's correct position, which is to put pressure on the yoke, I think, which pushes castle gear up against gear. At least thats what it all looked like. Worked the charm the second time. One more thing - I've read different opinions on what position the crown should be in when releasing. I've always used the third position for removal and installation. Zig seems to go for the first position (winding). Anyone have the definitive on this? Does it really matter. I was successful in the third (hand setting) position. Thanks for the info and an hour of very relaxing watch repairing. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now