redwatch Posted November 30, 2010 Report Share Posted November 30, 2010 I have a nice vintage Longines that belongs to a co-worker of mine. The crown came off of the stem and I told him I would take a look at it for him. It has a snap off case back, but it is smooth and flush to the edge of the watch case. There are no apparent gaps and I cannot get my watch knife in between the very small grove between the case back and watch case. Any suggestions or tricks? I verified that it is a snap on case back. I tried a sticky ball and the case back just spins around Link to comment Share on other sites More sharing options...
Justasgood Posted November 30, 2010 Report Share Posted November 30, 2010 Are you sure it is not a toploader case. Many Longines load from the crystal side. Link to comment Share on other sites More sharing options...
redwatch Posted November 30, 2010 Author Report Share Posted November 30, 2010 I thought of that. However, even if that is the case, how do I pop the crystal out? And then, once I figure that out, how would I remove the dial and movement? How would I release the stem? Link to comment Share on other sites More sharing options...
Nanuq Posted November 30, 2010 Report Share Posted November 30, 2010 Pffffffffft. It's easy to get snap-on backs off. You just need better aim than I possess. Link to comment Share on other sites More sharing options...
Justasgood Posted November 30, 2010 Report Share Posted November 30, 2010 I thought of that. However, even if that is the case, how do I pop the crystal out? And then, once I figure that out, how would I remove the dial and movement? How would I release the stem? If it is a Top Loader case, the stem is a 2 piece Male/female. You need a crystal compression tool(Looks like a 20 talon claw). I have used a pointed screwdriver at the 6 o'clock location next to the bezel and pushed in and up. High risk but effective. Can you post a pic? I have a crystal wrench I can send you. Link to comment Share on other sites More sharing options...
hiker01 Posted November 30, 2010 Report Share Posted November 30, 2010 "Pffffffffft. It's easy to get snap-on backs off. You just need better aim than I possess." Link to comment Share on other sites More sharing options...
redwatch Posted November 30, 2010 Author Report Share Posted November 30, 2010 Here's a couple of pics Link to comment Share on other sites More sharing options...
redwatch Posted November 30, 2010 Author Report Share Posted November 30, 2010 Pffffffffft. It's easy to get snap-on backs off. You just need better aim than I possess. Ouch....that could be bad. I suppose it would be best to remove the watch from the wrist before attempting to use that specialized case back remover, huh? Link to comment Share on other sites More sharing options...
Justasgood Posted November 30, 2010 Report Share Posted November 30, 2010 Well it is a 3 piece case. Your gonna need patience and determination as the gunk probably has it locked. It looks like an opening near the lug. Are you using a case knife? Link to comment Share on other sites More sharing options...
Justasgood Posted November 30, 2010 Report Share Posted November 30, 2010 BTW, that houses a very nice Longines caliber 12.68z movement. Very desirable among Longines collectors. Is the case 35.5mm? Nice piece. Link to comment Share on other sites More sharing options...
redwatch Posted November 30, 2010 Author Report Share Posted November 30, 2010 BTW, that houses a very nice Longines caliber 12.68z movement. Very desirable among Longines collectors. Is the case 35.5mm? Nice piece. Yes - it is 35.5mm in diameter. I am using a case knife with it, but even if I attempt from the lug sides I get no where. Is there any other fancy trick to it that I am missing? Now that you have seen a pic, do you think the caseback should come off? Link to comment Share on other sites More sharing options...
Justasgood Posted November 30, 2010 Report Share Posted November 30, 2010 Yes it should come off. Try a new razor blade. Other than that or a case knife with a clean edge, I am stumped. Link to comment Share on other sites More sharing options...
redwatch Posted November 30, 2010 Author Report Share Posted November 30, 2010 Yes it should come off. Try a new razor blade. Other than that or a case knife with a clean edge, I am stumped. Ok! Got it off. Now. How do I get the movement out? Link to comment Share on other sites More sharing options...
redwatch Posted November 30, 2010 Author Report Share Posted November 30, 2010 With K's help, I was able to do a little searching around and it looks like, based on the serial number of the movement, that this watch was manufactured in 1948 and has a cal 12.68z movement in it. Link to comment Share on other sites More sharing options...
offshore Posted November 30, 2010 Report Share Posted November 30, 2010 @Red, The dial is bigger than the exit hole, so you are still going to have to remove the glass. You need one of these.- http://watchbitz.com.au/shop/index.php?_a=viewProd&productId=112 You may be able to release the stem from the rear, or as mentioned earlier, it is a split stem, which you will "break" apart from the dial side. Google "split stem" for a description. Once you get the plexi out, shoot me an OD, I more than likely have a replacement. O/S Link to comment Share on other sites More sharing options...
redwatch Posted November 30, 2010 Author Report Share Posted November 30, 2010 @Red, The dial is bigger than the exit hole, so you are still going to have to remove the glass. You need one of these.- http://watchbitz.com.au/shop/index.php?_a=viewProd&productId=112 You may be able to release the stem from the rear, or as mentioned earlier, it is a split stem, which you will "break" apart from the dial side. Google "split stem" for a description. Once you get the plexi out, shoot me an OD, I more than likely have a replacement. O/S Thanks O/S! So, does the crystal lift compress the crystal making the O/D smaller so it comes out through the top? Link to comment Share on other sites More sharing options...
Justasgood Posted November 30, 2010 Report Share Posted November 30, 2010 Yes.Red, I can send you my crystal tool if you need it. let me know, kurt. Link to comment Share on other sites More sharing options...
redwatch Posted November 30, 2010 Author Report Share Posted November 30, 2010 Yes. Red, I can send you my crystal tool if you need it. let me know, kurt. That would be awesome K. Thank you for the offer. I should probably buy one down the road, but it would be good to test it out first. I'll PM you Link to comment Share on other sites More sharing options...
redwatch Posted December 2, 2010 Author Report Share Posted December 2, 2010 @Red, The dial is bigger than the exit hole, so you are still going to have to remove the glass. You need one of these.- http://watchbitz.com.au/shop/index.php?_a=viewProd&productId=112 You may be able to release the stem from the rear, or as mentioned earlier, it is a split stem, which you will "break" apart from the dial side. Google "split stem" for a description. Once you get the plexi out, shoot me an OD, I more than likely have a replacement. O/S Justasgood was nice enough to loan me his wonderful Crystal Removal Tool, but there isn't much of a lip to grab onto on the side of the crystal and it keeps slipping off. It starts to grab it and I am able to turn the crystal in the case, but as soon as I tighten up the tool just a little bit more, it slips off. Any tips/tricks?? Link to comment Share on other sites More sharing options...
redwatch Posted December 2, 2010 Author Report Share Posted December 2, 2010 Here's a quick side profile: Link to comment Share on other sites More sharing options...
Justasgood Posted December 2, 2010 Report Share Posted December 2, 2010 Sorry, as a 3 piece case, get a razor under the bezel and the ring/crystal will come off together. Brain fart in suggesting the crystal tool.....DOH! Link to comment Share on other sites More sharing options...
redwatch Posted December 2, 2010 Author Report Share Posted December 2, 2010 Sorry, as a 3 piece case, get a razor under the bezel and the ring/crystal will come off together. Brain fart in suggesting the crystal tool.....DOH! Got it! Thanks K!!! Link to comment Share on other sites More sharing options...
redwatch Posted December 2, 2010 Author Report Share Posted December 2, 2010 Ok. So now that I have everything pulled apart, the next question is: how to remove the stem? I see a very small hole immediately to the left of the stem on the side of the movement, or a small screw to the right on the bottom of the movement. My guess is I turn the small screw to the right, and unscrew it to loosen the stem? I await the experts Here's some pics: Link to comment Share on other sites More sharing options...
Justasgood Posted December 3, 2010 Report Share Posted December 3, 2010 The small hole to the left is the screw that holds the dial. The small screw on top and right is the one you need to loosen. Careful you don't back it all the way out. Just loosen, pull on the stem, loosen, pull on the stem until the stem comes out. When installing the new stem, make sure you twist it as you install it. Once properly seated, tighten that little screw(don't over tighten). Way to go Red. That is such a nice Longines. I really miss the few that I had. Link to comment Share on other sites More sharing options...
redwatch Posted December 3, 2010 Author Report Share Posted December 3, 2010 Wow K! You've had a few of these huh?? That Wittnauer is a beauty!! Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now