projectologist Posted November 14, 2011 Report Share Posted November 14, 2011 One man's passion can create some amazing objects that stand alone as a tribute to said passion. OK, OK that was probably a little over the top for a CG, but it's one helluva CG that I've had the pleasure of fine-tuning the final shape of, and applying a proper brushed finish to. I hope that I have done it justice. The straight wire lever pin (per gen) still needs to be cut to length, and the inner lever tip sized to properly engage the crown. This is one of a small batch that I was fortunate to acquire. Will more be produced again in the near future?... I don't know for sure, but I bet somewhere a file on a thumb-drive is ready to go when the time is right again. • Disclaimer... please do not email or send me any PM's inquiring where I got the CG. It really doesn't matter anyway as there are no more to be had. But take this post as evidence that an essentially 1:1 Pre-V CG can and has been produced and will hopefully be available again someday. After studying Pre-V CG pics until my eyes crossed I realized that during the era they were manufactured, dimensions and tolerances varied quite a bit. Case-in-point is the amount of chamfer at the top of the hole for the lever pin. From barely noticeable to noticeably wide and all amounts in-between. The same with the amount of lever tip length extending beyond the CG body. Gen pics added (a little blurry from up-rezing, but should suffice for comparison). Link to comment Share on other sites More sharing options...
Watchmeister Posted November 14, 2011 Report Share Posted November 14, 2011 Very pretty. That is one gorgeous block of steel. Link to comment Share on other sites More sharing options...
StormTooper4 Posted November 14, 2011 Report Share Posted November 14, 2011 Very Solid looking CG , what is it going on? Link to comment Share on other sites More sharing options...
dluddy Posted November 14, 2011 Report Share Posted November 14, 2011 Very nice Link to comment Share on other sites More sharing options...
projectologist Posted November 14, 2011 Author Report Share Posted November 14, 2011 Very Solid looking CG , what is it going on? 201A build. Case set and crown being tweaked. When they arrive I'll do the final assembly. Still need to lume the FGD hands. This is what I've got so far (CG prior to applying the brushed finish)... Link to comment Share on other sites More sharing options...
PeteM Posted November 14, 2011 Report Share Posted November 14, 2011 Looks great mate... nice work makes me look more forward to getting mine in my hand and on my watch Link to comment Share on other sites More sharing options...
hackR Posted November 15, 2011 Report Share Posted November 15, 2011 looks great...what was the process/tools used for the brushed finish?... thanks for sharing... Link to comment Share on other sites More sharing options...
blue_sphere Posted November 15, 2011 Report Share Posted November 15, 2011 Wow man thats a beauty of a CG... I hope what you say is true and it will be avail soon Link to comment Share on other sites More sharing options...
projectologist Posted November 15, 2011 Author Report Share Posted November 15, 2011 looks great...what was the process/tools used for the brushed finish?... thanks for sharing... Thanks. I used only one grit (3M 320 Wet/Dry) for all surfaces, including the lever. The sandpaper was trimmed into strips and mounted to paint stirring sticks with thin carpet tape. I used a friend's advice that all brushing should be in one direction only (never back and forth). I either drew the CG body across a stationary sanding strip or drew the strip across a carefully clamped CG. I took my time and made sure every stroke ran as parallel as possible with the surface length-wise. Link to comment Share on other sites More sharing options...
squashlovernk Posted November 15, 2011 Report Share Posted November 15, 2011 That CG is the NUTZ! I LOVE the concentric circular pattern you achieved on the CG pin and also the chamfer around the CG pin hole. Man, that CG has got to be one of the best, if not the best, rep CGs I've EVER seen on any of these board. Well done sir!!!!! Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now