Ephry73 Posted February 10, 2012 Report Share Posted February 10, 2012 Anyone in NYC or nearby areas with this tool set for me to borrow for the weekend? The tube on my Tudor just broke(stupid old beds at the hospital) and I need to replace it. I twas thinking of molding the tool with clay and then use JB weld and ferrous powder to make a set. Thanks in advance. E Link to comment Share on other sites More sharing options...
Nanuq Posted February 10, 2012 Report Share Posted February 10, 2012 I have used a triangular file or a good fitting screwdriver in the past, when I didn't have the right tool. You can heat the case to soften up the sealant and sometimes those rascals will come right out. To re-install I use the same tool, then I screw the crown onto the tube, and tighten that way. That compresses the o-ring inside the crown, then runs the crown (and tube) right down until the crown bottoms out against the case, or the tube bottoms in its threads. So far no complaints with that technique. Link to comment Share on other sites More sharing options...
Ephry73 Posted February 10, 2012 Author Report Share Posted February 10, 2012 Thanks Nanuq. I have tried the file route but don't want to damage the teeth. Needless to say I'm MAD that this happened. The watch had turned out exactly how I wanted it. LOL I have to not only heat the case(OCD me used epoxy to seal it) but carefully tap the tail out of the case. Now in the search for another Gen tube. E Link to comment Share on other sites More sharing options...
JoeyB Posted February 11, 2012 Report Share Posted February 11, 2012 If you have a set of screw extractors, 'easy-outs' the small one will take out the broken tube safely. Harbor Freight has them http://www.harborfreight.com/12-piece-screw-extractor-set-40349.html as do hardware stores and auto parts stores, under $10. If the tube was epoxied in try heating the screw extractor, get it good and hot - it is hardened steel, and melt the epoxy by putting the heated screw extractor in the tube hole a few seconds and then start unscrewing it. Much better than heating the case, and more precise with the heat. Link to comment Share on other sites More sharing options...
Ephry73 Posted February 11, 2012 Author Report Share Posted February 11, 2012 Thanks Joey. Not looking forward to this repair, but I have to. E Link to comment Share on other sites More sharing options...
JoeyB Posted February 11, 2012 Report Share Posted February 11, 2012 It's not too tough at all. The epoxy melts easily and the extractor 'bites' and unscrews it like a wrench would. And don't get mad, we break tubes all the time! It is a 'weak link'. Link to comment Share on other sites More sharing options...
Ephry73 Posted February 11, 2012 Author Report Share Posted February 11, 2012 @ Jey Thanks man. @NAnuq, I sent you a PM regarding Snowflakes E Link to comment Share on other sites More sharing options...
Jkay Posted February 11, 2012 Report Share Posted February 11, 2012 Just a thought, but if you use the crown as a depth guide when you seat the tube, what happens when the crown gasket starts to age and compress .. haven't you taken away the ability to screw down the crown further, compensating for the flattening gasket? Link to comment Share on other sites More sharing options...
Nanuq Posted February 11, 2012 Report Share Posted February 11, 2012 Just a thought, but if you use the crown as a depth guide when you seat the tube, what happens when the crown gasket starts to age and compress .. haven't you taken away the ability to screw down the crown further, compensating for the flattening gasket? Very good point. That occurred to me as I installed my first one that way, and my immediate response as I screwed the tube in, was to "go big, or go home". So I quickly screwed it down TIGHT, then just as quickly backed the crown off. Then I waited for the sealant on the tube threads to set up tight. That was 2 years ago, and since then I've been careful not to overtighten the gen Triplock crown I used to install the tube. I screw it down and feel the gasket compress, and it juuuuust bottoms out as the gasket gets smashed. Then I don't go any tighter. It hasn't gotten looser over 2 years and I swim with it every week. So far so good. I suppose some day the gasket will get smooshed and I won't feel it compress like this any more. Then, I'll just pull the stem, pick out the old gasket from the crown and put in another. I've got a little envelope full of the little rascals. Link to comment Share on other sites More sharing options...
superlative Posted February 12, 2012 Report Share Posted February 12, 2012 (edited) Submerse the case in boiling hot water for 10 minutes. This will loosen the epoxy. Applying heat directly or otherwise can and may discolour your case. Edited February 12, 2012 by superlative Link to comment Share on other sites More sharing options...
Ephry73 Posted February 12, 2012 Author Report Share Posted February 12, 2012 Thanks guys. Btw, thrvthing that really annoys me is the fact that the crown was oriented just right. I got a full gasket kit full of all of the o-rings from Clark's when I first started this build. Gary will help anyone with that. Link to comment Share on other sites More sharing options...
cjjoyce1 Posted February 12, 2012 Report Share Posted February 12, 2012 I've used a torx-tip screwdriver before. Can't recall the number, though. Also a small punch inserted to friction fit works. Link to comment Share on other sites More sharing options...
Ephry73 Posted February 13, 2012 Author Report Share Posted February 13, 2012 I bet I can try that soon Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now