the_rymeister Posted May 24, 2012 Author Report Share Posted May 24, 2012 Hi Ry, just seeing over on RWI (taka's corner) that he is apparently off travelling the world and no longer taking orders. If he is back in business soon remains to be seen. Thanks for the heads up bud I'll try contact chief and see what the cost is Link to comment Share on other sites More sharing options...
om3ga_guy Posted May 25, 2012 Report Share Posted May 25, 2012 (edited) Great work Ry and great pics, the pearl is always a issue with me, mods can be done well but it's very hard to compete with proper bezel. Next move now will be the AR, even if you dont get a gen (which are a bit crazy in price) something like Taka AR on rep crystal is extremely close in transparency to the omega double AR. Good transparency really makes the dial and lume pop. Chief does very similar also. Back to the PO insert topic for a second, we all know that you can do a gen pearl mod to an aftermarket insert. In photos (if the pearl mod is done well) the bezel looks great. But once you have it done and on the wrist there's a few things you realize. The aftermarket insert has a much different finish than the gen. The gen has this reflective gloss or whatever and it cant be replicated. The quality of the printing is not as crisp and after excessive wrist time the rep insert fades fast. Especially the edges. I realize gen bezels are gen bezels and you cant compare a $25 rep insert to them, but I just wanted to point a few things out for those who haven't don't the mod. I too went to a gen bezel and I could never go back Edited May 25, 2012 by om3ga_guy Link to comment Share on other sites More sharing options...
sneed12 Posted May 25, 2012 Report Share Posted May 25, 2012 JB Weld I hope you never want to take the pieces apart... I just use hypo cement for bezel inserts. Also, I install the insert after the bezel is on the watch, to make sure the triangle is lined up to the 12. Looks like you got yours right though. Did you mark it or something? Link to comment Share on other sites More sharing options...
the_rymeister Posted May 25, 2012 Author Report Share Posted May 25, 2012 JB Weld I hope you never want to take the pieces apart... I just use hypo cement for bezel inserts. Also, I install the insert after the bezel is on the watch, to make sure the triangle is lined up to the 12. Looks like you got yours right though. Did you mark it or something? I didn't want it to fall off , I marked the lines up to the points on the bezel teeth so it would be exactly on the click of 12oclock Back to the PO insert topic for a second, we all know that you can do a gen pearl mod to an aftermarket insert. In photos (if the pearl mod is done well) the bezel looks great. But once you have it done and on the wrist there's a few things you realize. The aftermarket insert has a much different finish than the gen. The gen has this reflective gloss or whatever and it cant be replicated. The quality of the printing is not as crisp and after excessive wrist time the rep insert fades fast. Especially the edges. I realize gen bezels are gen bezels and you cant compare a $25 rep insert to them, but I just wanted to point a few things out for those who haven't don't the mod. I too went to a gen bezel and I could never go back Looks great buddy Link to comment Share on other sites More sharing options...
glippy01 Posted May 27, 2012 Report Share Posted May 27, 2012 I think Ofrei has Gen. crystals for around $181.00 USD. You really should think about topping off the fine job you did with the insert with a Gen crystal and consider it done. Link to comment Share on other sites More sharing options...
the_rymeister Posted May 27, 2012 Author Report Share Posted May 27, 2012 Think I will when I get some funds together Link to comment Share on other sites More sharing options...
Logan Posted May 28, 2012 Report Share Posted May 28, 2012 I wonder why the bezel construction is so different on the rep? You'd think there wasn't any real reason to not do the genuine system? The only explanation I can come up with is needing more surface area for the insert to adhere to, allowing lower tolerances between the two parts, vs the snap in fitting that the real part uses. Link to comment Share on other sites More sharing options...
DemonSlayer Posted May 28, 2012 Report Share Posted May 28, 2012 JB Weld I hope you never want to take the pieces apart... I just use hypo cement for bezel inserts. I've found Hypo cement to be quite weak when installing inserts, when you want to keep your insert for the long run you need something stronger. Link to comment Share on other sites More sharing options...
rhc22 Posted May 28, 2012 Report Share Posted May 28, 2012 I wonder why the bezel construction is so different on the rep? You'd think there wasn't any real reason to not do the genuine system? The only explanation I can come up with is needing more surface area for the insert to adhere to, allowing lower tolerances between the two parts, vs the snap in fitting that the real part uses. I think you are right, the Omega method requires tighter tolerances and repeatability. High end watches are fine pieces of engineering, goes some way to the difference in cost! Link to comment Share on other sites More sharing options...
toasternz Posted June 5, 2012 Report Share Posted June 5, 2012 I think Ofrei has Gen. crystals for around $181.00 USD. You really should think about topping off the fine job you did with the insert with a Gen crystal and consider it done. Can someone please help me find this on the Ofrei site? This here looks like Crystal for the right case number [45mm PO] but is $36.00 so obviously not right! http://www.ofrei.com/page_168.html#13466 Link to comment Share on other sites More sharing options...
toasternz Posted June 6, 2012 Report Share Posted June 6, 2012 Can someone please help me find this on the Ofrei site? This here looks like Crystal for the right case number [45mm PO] but is $36.00 so obviously not right! http://www.ofrei.com..._168.html#13466 Nevermind, obviously the one with the AR and Saphire is $181 as posted above, just wasn't obvious on first look. Link to comment Share on other sites More sharing options...
cougar1 Posted June 6, 2012 Report Share Posted June 6, 2012 Yep this one: Omega Sapphire Crystal 062SB3065 Fits cases 168.1651, 168.1653 OME-SB3065 $181.00 Link to comment Share on other sites More sharing options...
toasternz Posted June 25, 2012 Report Share Posted June 25, 2012 (edited) Guys, I'm about to attempt this shortly and have the watch stripped down but cannot get the bezel off. Since the crystal etc is now out do I really need to keep fighting with the Bezel or can I just follow The_Rymeister's steps except with the bezel attached to the watch? Assume a little bit of heat and the insert will come off cleanly. Thanks. Edited June 25, 2012 by toasternz Link to comment Share on other sites More sharing options...
cougar1 Posted June 25, 2012 Report Share Posted June 25, 2012 The bezel shouldn't be that difficult to come off, have you got a cheap bezel remover or even a good case knife? I'm sure ry will fill us in, I've never done the mod but it would certainly be much less hassle if you can get that bezel off. Link to comment Share on other sites More sharing options...
the_rymeister Posted June 25, 2012 Author Report Share Posted June 25, 2012 Hi toasternz the bezel shouldn't be too much of a problem removing, all I done was simply push a case back knife or a sharp thin knife between the bezel and one of the watch lugs and it pooped straight off, may be worth putting a piece of tape over the.ug your going to lever on to stop danages, but it should nt be hard work to remove. Also the mod would be a lot easier with the bezel off the watch, hope this helps buddy Link to comment Share on other sites More sharing options...
toasternz Posted July 5, 2012 Report Share Posted July 5, 2012 (edited) Hi toasternz the bezel shouldn't be too much of a problem removing, all I done was simply push a case back knife or a sharp thin knife between the bezel and one of the watch lugs and it pooped straight off, may be worth putting a piece of tape over the.ug your going to lever on to stop danages, but it should nt be hard work to remove. Also the mod would be a lot easier with the bezel off the watch, hope this helps buddy Thanks mate, worked out well in the end, you can see the result here: http://www.rwg.cc/to...ing-gen-vs-rep/ I still wasn't able to get the bezel off so did the mod with the bezel attached and the crystal out, to be honest that worked really well! Edited July 5, 2012 by toasternz Link to comment Share on other sites More sharing options...
kbh Posted July 5, 2012 Report Share Posted July 5, 2012 That JB Weld may be a little overkill. You'll never be able to get if off again without serious damage to something. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now