olga Posted January 18, 2007 Report Share Posted January 18, 2007 I bought some powder from Glow Inc. just to try and practice with before using Tritec's product. Anyway here is a first attempt at a hand with this powder. Link to comment Share on other sites More sharing options...
FxrAndy Posted January 18, 2007 Report Share Posted January 18, 2007 That looks ok for a first attempt how does it look in the light? Link to comment Share on other sites More sharing options...
olga Posted January 18, 2007 Author Report Share Posted January 18, 2007 It looks ok in the light with a uniform color and consistancy. It does not look good compared to a tritec lumed hand, but that is not my fault but rather the fault of the powder. The powder is a little to green in the light and the crystal size is way to big, to the point that it is noticeable with the naked eye. Link to comment Share on other sites More sharing options...
FxrAndy Posted January 18, 2007 Report Share Posted January 18, 2007 As long as you are happy with it that is all that matters, i have read that some people regrind the powder in a petstel and mortar. What did you use as i binder? Link to comment Share on other sites More sharing options...
Tom Posted January 18, 2007 Report Share Posted January 18, 2007 As long as you are happy with it that is all that matters, i have read that some people regrind the powder in a petstel and mortar. What did you use as i binder? May I ask what you used to apply the powder? I am (probably foolishly) going to try a lume job using Tritec in the next few weeks but don't know what to use, and can't find an oiler, which I know is what The Zigmeister uses. Link to comment Share on other sites More sharing options...
olga Posted January 18, 2007 Author Report Share Posted January 18, 2007 The binder was matte clear lacquer. Unfortunately, Tom I also used an oiler. 2 of them actually. If you look close at the picture you'll notice that the hand is on an oiler. You could use a very small screwdriver as well, say a 50 or 60. Link to comment Share on other sites More sharing options...
sssurfer Posted January 19, 2007 Report Share Posted January 19, 2007 Good work, olga! I used ReadySetGlo/GlowPaintPro powders, and they are way too coarse too. Crushing/milling them helped. Tom, you may easily find oilers on eBay. Link to comment Share on other sites More sharing options...
olga Posted January 19, 2007 Author Report Share Posted January 19, 2007 I've tried the mortar and pestal route, but unfortunately I was unable to get the stainless steel model and had to settle for marble. Well, when you grind the powder in the marble you end up creating some marble powder also and it makes the glow powder dirty looking. Link to comment Share on other sites More sharing options...
sssurfer Posted January 19, 2007 Report Share Posted January 19, 2007 I've tried the mortar and pestal route, but unfortunately I was unable to get the stainless steel model and had to settle for marble. Well, when you grind the powder in the marble you end up creating some marble powder also and it makes the glow powder dirty looking. I too started with a marble mortar+pestal, and ended up with a glass bottle or jar rolling on a (thick ) glass plate. Link to comment Share on other sites More sharing options...
olga Posted January 19, 2007 Author Report Share Posted January 19, 2007 I found someone else who sells a 5 - 10um powder. It is only a little more than double the cost of glow inc. powder, but pratically free when compared to tritec. So I'm going to give them a shot and see how it works out. I'll post the results and source after I've tried it. Link to comment Share on other sites More sharing options...
fitmic Posted January 19, 2007 Report Share Posted January 19, 2007 I usually use my credit card to crush it before inhaling... WAIT! We're talking about coke right? Sorry from hijacking, I just couldn't resist! Link to comment Share on other sites More sharing options...
sssurfer Posted January 20, 2007 Report Share Posted January 20, 2007 I found someone else who sells a 5 - 10um powder. Does "um" stand for microns? If so, an exceptionally fine powder! Main doubts on such a fine powder are obviously on how long its glow lasts. Let us know what you will find. Link to comment Share on other sites More sharing options...
maxmilian Posted January 20, 2007 Report Share Posted January 20, 2007 Is there any good "tutorial" on how to relume ? Link to comment Share on other sites More sharing options...
olga Posted January 20, 2007 Author Report Share Posted January 20, 2007 Does "um" stand for microns? If so, an exceptionally fine powder! Main doubts on such a fine powder are obviously on how long its glow lasts. Let us know what you will find. I believe they are using um for microns. They offer 4 grades 40-65, 20-40, 10-15 and 5-10. Yes, the smaller the powder the less bright they glow. In this case it is about 1/3 the brightness from the coursest to finest powder. They claim the maximum amount of time that the powder is glowing to a point perceivable by the human eye is as follows: 40-65 6800 minutes 20-40 4700 minutes 10-15 3600 minutes 5-10 1800 minutes Link to comment Share on other sites More sharing options...
sssurfer Posted January 21, 2007 Report Share Posted January 21, 2007 Well, 1800 minutes are 30 hours! Personally I keep doubts about it. Possibly they are referring to a perfect eye after a 30 hours accustoming in complete darkness. And 'perceivable by the human eye' is a completely different matter from 'perceivable by the man'. Human photosensitive molecules in the retina may react to a single photon while the owner stays completely unaware about it. Please let us know what you will find, I am very interested. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now