beever Posted September 21, 2007 Report Share Posted September 21, 2007 I dont know if I described it correctly but, on Panerais with the large crown guard, there is a lever that closes into the guard and against the crown of the watch. On my rep, and from what i have gathered on almost every rep, this pin is wobbly when in the open position. I have read for hours with no solution. I heard a vice to pinch the sides, some wire tubing trimmed to shim the hole. In my case, it seems that it wiggles from side to side and would require a washer or shim of some kind (or vice) to make it tight. What is the solution..simple I hope. Link to comment Share on other sites More sharing options...
sssurfer Posted September 21, 2007 Report Share Posted September 21, 2007 The ubiquitary problem on reps is that the lever is loose when in opened position, not that the lever pin is wobbly. Are you sure that it is your pin to be loose? (no pun intended) Link to comment Share on other sites More sharing options...
beever Posted September 22, 2007 Author Report Share Posted September 22, 2007 yup, loose when in open position and fine when closed. just annoying really. Link to comment Share on other sites More sharing options...
sssurfer Posted September 22, 2007 Report Share Posted September 22, 2007 Ok, you may try the usual fixes for the floppy lever problem. 1. Quick-and-dirty: Remove the pin (with the same tool used to remove bracelet links -- have a look here). Fill the hole in the crown guard and the lever, where the pin was, with silicon. Reinstall the pin. Clean any silicon excess. Wait 24 hrs with the lever in the closed position before moving it again. Or 2. The correct way: Remove the pin as in 1. Get a piece of electric wire that could accept the pin inside the rubber insulant, remove the copper threads, put the pin inside the insulant in place of the copper threads. Measure the wire thickness (diameter) with a micrometer, where the pin is. Remove the lever and enlarge its hole (where the pin was) with a dremel and a drill tip that diameter. Remove the pin from the insulant (you may sacrifice the insulant if this is tricky). Cut a piece of insulant as long as the lever's thickness. Put the insulant inside the enlarged hole of the lever. Mount the lever back in the crown guard. Push the pin back in its hole in the crown guard and lever. This way you will make a rubber gasket (or a very thin silicon gasket, with method 1) around the pin. This should keep the pin firm and it will get you rid of the floppy lever. Link to comment Share on other sites More sharing options...
sssurfer Posted September 24, 2007 Report Share Posted September 24, 2007 I just wonder why I spent my time to post this just not to even getting a "fuck you" reply... Link to comment Share on other sites More sharing options...
Highflyingclive Posted September 24, 2007 Report Share Posted September 24, 2007 I'll avoid (with regret) the obvious response and thank you, instead. One of my Pams is a possible candidate for the quick and dirty cure... it isn't too sloppy - but if it starts to irritate me, I'll be pumping silicone into the hole. You post saved for future reference, Thank you. Link to comment Share on other sites More sharing options...
beever Posted September 24, 2007 Author Report Share Posted September 24, 2007 Your solution was not correct for my situation. The issue wasnt the hole, but the fact that the opening for the CG pin was too wide. Tightening the pin would not keep it from wobbling so, no amount of silicone or wire insulation would fix the lever, in my case anyway. Pressure was needed to "pinch" the sides of the crown guard closer togetherby a fraction, and then the lever was tight. I also ruined the crown guard by using a pair of plyers with teeth on it, even though I taped them up pretty good, they still left a mark so I traded one small problem for another larger one. However, the solution worked perfectly and the pin no longer wiggles so, in the future, anyone trying this should be careful to use plenty of protection on the guard before applying pressure. Link to comment Share on other sites More sharing options...
PAMman Posted September 24, 2007 Report Share Posted September 24, 2007 The wire insulation is similar to the Jimmy Fu setup, but I have found a childs (girls) toy / craft material which is very good. This is fine, coloured, plastic tubing that girls twist and plait to make wristbands and key fobs etc. I don't know what it is called but ask any 10 or 12 year old and they should be able to point you in the right direction. It's finer than most readily available electrical wire insulation and just the correct size. Just steal some off your neighbours kid. Link to comment Share on other sites More sharing options...
Victoria Posted September 25, 2007 Report Share Posted September 25, 2007 Your solution was not correct for my situation. The issue wasnt the hole, but the fact that the opening for the CG pin was too wide. Tightening the pin would not keep it from wobbling so, no amount of silicone or wire insulation would fix the lever, in my case anyway. Pressure was needed to "pinch" the sides of the crown guard closer togetherby a fraction, and then the lever was tight. I also ruined the crown guard by using a pair of plyers with teeth on it, even though I taped them up pretty good, they still left a mark so I traded one small problem for another larger one. However, the solution worked perfectly and the pin no longer wiggles so, in the future, anyone trying this should be careful to use plenty of protection on the guard before applying pressure. And: "Thanks for all your help, Sssurfer." I'm not Miss Manners. But a nice thank you wouldn't have gone amiss, Beever, whatever the solution. Link to comment Share on other sites More sharing options...
georgegrasser Posted September 25, 2007 Report Share Posted September 25, 2007 And: "Thanks for all your help, Sssurfer." I'm not Miss Manners. But a nice thank you wouldn't have gone amiss, Beever, whatever the solution. No no no Victoria. Sssurfer failed to completly understand the problem and took a stab at one possible fix. When helping someone you must account for any and all possiblites of what is wrong. Analyze the problem and come up with the solutions. Then list in order every single possible repair. I was actually disapointed Sssurfer failed in this case, and I hope when I go to him with a problem that he actually takes the time to ensure my complete satisfaction. It is clear that Sssurfer did not want to spend the time to adequately find a solution. His failure is monumental. There is no defence. Link to comment Share on other sites More sharing options...
Victoria Posted September 25, 2007 Report Share Posted September 25, 2007 I was actually disapointed Sssurfer failed in this case, and I hope when I go to him with a problem that he actually takes the time to ensure my complete satisfaction. It is clear that Sssurfer did not want to spend the time to adequately find a solution. His failure is monumental. There is no defence. George, it's getting so that I have to put on the Secret RWG Decoder Ring to read your posts. Since only one person can possess it at a time, I fear dire consequences when others read them! Link to comment Share on other sites More sharing options...
POTR Posted September 25, 2007 Report Share Posted September 25, 2007 Actually, the Beev may have gotten lost and not have been able to find his way back to this thread again... I am sure he will say thanks once he figures out how to find out where he has been, or how to use the search facilities... Link to comment Share on other sites More sharing options...
sssurfer Posted September 25, 2007 Report Share Posted September 25, 2007 Btw, maybe -- just maybe -- I could have figured a solution should beever had not used the word "pin" as a synonim of "lever"... Actually, I got what he was meaning only after his second post here. And then it was too late to prevent me from my monumental failure. Link to comment Share on other sites More sharing options...
earlgrey-erfurt Posted September 25, 2007 Report Share Posted September 25, 2007 some pics would have been very helpful before and after hope the follow, the after ones cheers helmut Link to comment Share on other sites More sharing options...
beever Posted September 26, 2007 Author Report Share Posted September 26, 2007 Hey guys, I am sorry I didnt say thank you, I very much appreciate all of the advice and help..sorry about that. In the future, and now that you know the correct issue, how would you correct this problem so others can learn and so I can too. THANK YOU FOR YOUR TIME! Seriously. Link to comment Share on other sites More sharing options...
P4GTR Posted September 26, 2007 Report Share Posted September 26, 2007 I can feel the love. Link to comment Share on other sites More sharing options...
ork Posted October 7, 2007 Report Share Posted October 7, 2007 I just wonder why I spent my time to post this just not to even getting a "fuck you" reply... Hey sssurfer, please don't feel unappreciated, there are plenty of lurkers out there who appreciate the info greatly. On behalf of all of us: Thank you! Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now