Justasgood Posted January 19, 2008 Report Share Posted January 19, 2008 wwhat are your thoughts on this case?.....and yes I know the insert isn't installed yet Accepts 1560/1570 movement, crown position/opening is where it should be so no shimming needed as with the MBW 5513 case. MBW 5513: MBW 5513: My MBW 5513 for comparison: Thanks, Kurt. Link to comment Share on other sites More sharing options...
alligoat Posted January 19, 2008 Report Share Posted January 19, 2008 The crown guards are the biggest drawback. The insides are ok, but the thickness on each side is too much- just like the MBW. Also the top and bottom taper (slope) from the case out to the front of the guards is all wrong. It could be rounded over w/ a file and polished and it would look better. On the bottom of a gen case there is no taper on the bottom of the crown guards, they're relatively flat. Removing metal from the outside of the guards to thin them up would also help- I think Pug did this on his MBW. But heck, you got a 1560 movt in there, that's an accomplishment in itself. Link to comment Share on other sites More sharing options...
predfan2001 Posted January 19, 2008 Report Share Posted January 19, 2008 (edited) Cgs look like the early pointed style to me. Like the early 60s models with gilt dials. Edited January 19, 2008 by predfan2001 Link to comment Share on other sites More sharing options...
Justasgood Posted January 19, 2008 Author Report Share Posted January 19, 2008 Cgs look like the early pointed style to me. Like the early 60s models with gilt dials. my thoughts exactly.....perhaps a little cg work to thin 'em up abit and a little edge polishing to soften the case lines. Link to comment Share on other sites More sharing options...
Justasgood Posted January 19, 2008 Author Report Share Posted January 19, 2008 The crown guards are the biggest drawback. The insides are ok, but the thickness on each side is too much- just like the MBW. Also the top and bottom taper (slope) from the case out to the front of the guards is all wrong. It could be rounded over w/ a file and polished and it would look better. On the bottom of a gen case there is no taper on the bottom of the crown guards, they're relatively flat. Removing metal from the outside of the guards to thin them up would also help- I think Pug did this on his MBW. But heck, you got a 1560 movt in there, that's an accomplishment in itself. The cg mods are the easy/fun part for me. What are your thoughts on the caseback stampings and the bezel teeth? Thanks. Link to comment Share on other sites More sharing options...
alligoat Posted January 19, 2008 Report Share Posted January 19, 2008 The case back stampings look ok to me. Comparing the bezel teeth to my gen 1680, the teeth are cut too far thru to the bezel insert on your 5512. They look softer which is ok. My gen bezel teeth and my WM 1680 both have smooth and well worn bezel teeth which only go 1/2 way into the bezel itself, like your 5513, only softer. But looking at Skeet and Urul- Vintage Rolex Sports Models- most of the bezel teeth appear to be cut thru to the bezel insert- but their pics are those damn computer retouched photos. From the back, your 5513 looks like the case got wallowed out on the back side when you installed your gen tube- that happened to me on my noob! Link to comment Share on other sites More sharing options...
Justasgood Posted January 19, 2008 Author Report Share Posted January 19, 2008 The case back stampings look ok to me. Comparing the bezel teeth to my gen 1680, the teeth are cut too far thru to the bezel insert on your 5512. They look softer which is ok. My gen bezel teeth and my WM 1680 both have smooth and well worn bezel teeth which only go 1/2 way into the bezel itself, like your 5513, only softer. But looking at Skeet and Urul- Vintage Rolex Sports Models- most of the bezel teeth appear to be cut thru to the bezel insert- but their pics are those damn computer retouched photos. From the back, your 5513 looks like the case got wallowed out on the back side when you installed your gen tube- that happened to me on my noob! That is due to the eta movement being thicker than the Rolex mov't. That is why I like the new case shown. It has the tube opening centered for the Rolex movement. I kept breaking stems on my 1560 in the MBW case and I got tired of trying to balance the shims and proper hand stack......so it looks like this new case......although very expensive, will bring my project to a conclusion. Thanks for the feedback, Kurt. Link to comment Share on other sites More sharing options...
alligoat Posted January 19, 2008 Report Share Posted January 19, 2008 So I guess this is a Jewelry and Watch case. If you're going to go to the trouble of putting a 1560 in there, a J&W case certainly makes sense- especially in light of the problems you had w/ the MBW case. It's a very nice watch and you've certainly gone to the highest level- a true franken! Congratulations. Link to comment Share on other sites More sharing options...
Justasgood Posted January 20, 2008 Author Report Share Posted January 20, 2008 So I guess this is a Jewelry and Watch case. If you're going to go to the trouble of putting a 1560 in there, a J&W case certainly makes sense- especially in light of the problems you had w/ the MBW case. It's a very nice watch and you've certainly gone to the highest level- a true franken! Congratulations. A who and what? Link to comment Share on other sites More sharing options...
alligoat Posted January 20, 2008 Report Share Posted January 20, 2008 http://www.jewelryandwatch.com/ This is Phong out in Arizona- the Vietnamese connection, so to speak. So I guess the next question would be, if this isn't a J&W case, where did it come from? Link to comment Share on other sites More sharing options...
Justasgood Posted January 20, 2008 Author Report Share Posted January 20, 2008 http://www.jewelryandwatch.com/ This is Phong out in Arizona- the Vietnamese connection, so to speak. So I guess the next question would be, if this isn't a J&W case, where did it come from? I have been in contact with another member regarding this case and he expressed an interest in getting. At the moment, the supplier lists only 1 in stock. So to be fair, I will reveal the source after hearing from said member as to his intent. I can say that the case I am getting, cost a fair bit less, and has the proper style bezel insert. It comes with no crown or tube, but I have easy access to those from my source New and in package. Also, it seems that upon closer inspection of the cases at www.jewelryandwatch.com, the spring bar holes look a tad small in diameter. Maybe it's just a bad angle. Stay tuned and thanks for your insights, Kurt. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now