t Posted August 14, 2009 Report Posted August 14, 2009 New batch of T48 crowns are ready on stock the T48 crown is now also available with 0.9mm stem size for all auto movements T48 SS 1.2mm T48 SS 0.9mm T48 Titanium 1.2mm T48 Titanium 0.9mm T48 PVD 1.2mm PVD crown is available for 1.2mm stem size only - not with 0.9mm. regards T
bertieng Posted August 14, 2009 Report Posted August 14, 2009 Good to know, T. Perhaps you can also list out the cost? Cheers.
Drulee Posted August 14, 2009 Report Posted August 14, 2009 Good to know, T. Perhaps you can also list out the cost? Cheers. I do believe you have to email him for that info
t Posted August 14, 2009 Author Report Posted August 14, 2009 guys i have a limited stock only... exspecially the titanium crowns and the new 0.9mm crowns are very rare... please place your order via email
coolfire Posted August 14, 2009 Report Posted August 14, 2009 Good job t! Super-fast shipping as well!
tanya Posted August 14, 2009 Report Posted August 14, 2009 AHHHHHHHH Tourby I just sent you an email I need beautiful T crowns!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
tanya Posted August 14, 2009 Report Posted August 14, 2009 Did i tell you guys how much I love T crowns!!! Now V how about another run of CG's And Pre V casebacks too!!!!
tanya Posted August 15, 2009 Report Posted August 15, 2009 Ordered Mine!!!! I wish I could have ordered twice as many!!
paneristi Posted August 16, 2009 Report Posted August 16, 2009 Ordered Mine!!!! I wish I could have ordered twice as many!! who is V. I urgently need a new CG
bertieng Posted August 22, 2009 Report Posted August 22, 2009 I have found the spec is different from the last batch. The top of the crown is much more recessed than the previous lot. If I adjust the stem to the length of having the crown sits flush to the case then the lever is too far away, the locking function is gone. If I make the stem long enough to retain the lever locking fucntion then it will leave a big gap between the crown and the case Perhaps T can chim in if I am correct on the spec variance of the two batches.
fitch Posted August 22, 2009 Report Posted August 22, 2009 (edited) Ai! that's not good news... I also hope that T can chim in, mine is waiting for me to pick it up at the post office and I was really looking forward to installing it Edited August 22, 2009 by fitch
Drulee Posted August 22, 2009 Report Posted August 22, 2009 I have found the spec is different from the last batch. The top of the crown is much more recessed than the previous lot. If I adjust the stem to the length of having the crown sits flush to the case then the lever is too far away, the locking function is gone. If I make the stem long enough to retain the lever locking fucntion then it will leave a big gap between the crown and the case Perhaps T can chim in if I am correct on the spec variance of the two batches. Was this one crown in particular (eg. SS 1.2)? Or did you get a few crowns from him and try them all?
t Posted August 22, 2009 Author Report Posted August 22, 2009 (edited) absolute no difference between batch 1 and 2. Same crowns and same quality... I don´t think that someone should have any problems... if he install the crowns correct. Edited August 22, 2009 by t
Drulee Posted August 22, 2009 Report Posted August 22, 2009 absolute no difference between batch 1 and 2. Same crowns and same quality... I don
Drulee Posted August 23, 2009 Report Posted August 23, 2009 sometimes it makes trouble to install the T48 crown, because not all CG and pins are absolute identical... minimal differences in measurements makes trouble to install the T48 crown. So please try it again (or on another watch or with another crown) Yes, I've especially noticed this with Jackson Tse's crown guards. I've had two SS and two titanium ones from him and the levers on them all have been sanded to a "nub" just barely touching the crowns he provides Oh well, you get what you pay for I've got a couple of your crowns on my PAMs, and they really do make quite a difference when winding and adding to the overall look of it. Do you still have the T60 as well?
t Posted August 23, 2009 Author Report Posted August 23, 2009 please install a thicker a a second plastic ring... probably it will fit better?
Drulee Posted August 23, 2009 Report Posted August 23, 2009 please install a thicker a a second plastic ring... probably it will fit better? I'm sorry, what do you mean by a "thicker and second plastic ring"?
bertieng Posted August 23, 2009 Report Posted August 23, 2009 please install a thicker a a second plastic ring... probably it will fit better? Sorry T, if you mean by adding an extra o-ring, it won't work coz it will push the stem out of the winding position. I don't mean to raise any complaints here, the T48 crowns are of superb finishes. I am still working on it how to retain the locking function of the lever in the T48.
t Posted August 23, 2009 Author Report Posted August 23, 2009 are you sure the left crowns are my crowns? i have check all my crowns and don
rolli Posted August 23, 2009 Report Posted August 23, 2009 1.) a second seal o-ring between the tube and crown is not a perfect solution, it's a totally wrong method. the correct guidelines for waterproofing and global proofing implies only one seal. one seal / gasket against the other is a dangerous zone. it's never 100 percent proof. 2.) the new t-crown with the deeper recess is only to apply in connection with the little hero crown-guard. this crown-guard has a longer lever extension and it's more qualified for a perfect adaption. rolli
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now