asciwhite Posted December 16, 2009 Report Share Posted December 16, 2009 Never modded a watch before, and I have to learn from my mistakes I guess. Apart from scre*ing up the pearl and destrying the keyless works.. so i have to change the whole bezel insert again, and send the watch out for repair. I think i did ok The watchmaterial pearl was HUGE compared to the one that came with the insert... and I botched the install. Anyways. You guys can say if i need to mod the CGs more or if it is close enough, and if there is something wrong with the install of the insert (apart from the obvious) have I got enough "lip" or too much? Link to comment Share on other sites More sharing options...
alligoat Posted December 16, 2009 Report Share Posted December 16, 2009 You're there with the cg's, looking good. The problem w/ recessing the insert on the SSD is that it makes the crystal height more pronounced- so I'd go w/ 'less is best' in this case. Better luck on your next insert. I used an x-acto knife to enlarge the hole before installing the WM pearl- worked OK- just go slowly and keep testing so you don't over enlarge. Link to comment Share on other sites More sharing options...
asciwhite Posted December 16, 2009 Author Report Share Posted December 16, 2009 Thanks alligoat $39 out the window for the insert Oh well, live and learn. The Sea-Dweller inserts are much more expensive than the Submariners. (wonder why?) Hope I can pry the broken insert off since i Gorilla glued it in.. Link to comment Share on other sites More sharing options...
alligoat Posted December 16, 2009 Report Share Posted December 16, 2009 Yeh, I don't use gorilla glue, or epoxy on inserts. I've used the GS Hypo-cement and done OK. It's not as strong, but it sure makes it easier if you're removing the insert! here's an insert for $24+, http://cgi.ebay.com/BLACK-BEZEL-INSERT-FIT-ROLEX-SEA-DWELLER-WATCH-PARTS_W0QQitemZ250506776975QQcmdZViewItemQQptZLH_DefaultDomain_0?hash=item3a535e118f Link to comment Share on other sites More sharing options...
asciwhite Posted December 16, 2009 Author Report Share Posted December 16, 2009 Yeh, I don't use gorilla glue, or epoxy on inserts. I've used the GS Hypo-cement and done OK. It's not as strong, but it sure makes it easier if you're removing the insert! here's an insert for $24+, http://cgi.ebay.com/...=item3a535e118f I have looked at that Only thing is I live in Norway, so have to add $10 for shipping (SUCKS) hehe But you can`t put a price on results achieved when done right. Link to comment Share on other sites More sharing options...
jmb Posted December 16, 2009 Report Share Posted December 16, 2009 I have been using clear silicone RTV adhesive on inserts. Seems to hold very well but is easy to "un-stick" stuff if needed. I also use RTV to affix emblems/badges, etc. to motorcycles after a repaint. I bought the following insert for my next ST project, I don't know if it would fit an SSD or not, though, but they probably have one. This was $14... http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=230373426919&viewitem=&sspagename=STRK%3AMEWNX%3AIT Link to comment Share on other sites More sharing options...
asciwhite Posted December 16, 2009 Author Report Share Posted December 16, 2009 I have been using clear silicone RTV adhesive on inserts. Seems to hold very well but is easy to "un-stick" stuff if needed. I also use RTV to affix emblems/badges, etc. to motorcycles after a repaint. I bought the following insert for my next ST project, I don't know if it would fit an SSD or not, though, but they probably have one. This was $14... http://cgi.ebay.com/...RK%3AMEWNX%3AIT Oh perfect.. Joink! Ref NO : 16660 is Sea-Dweller. Thanks jmp Edit: Hmmm the fonts look a bit fat on that one The other ones have much crisper fonts IMO.... Bought this one Watchbandman50 16660 insert Link to comment Share on other sites More sharing options...
lanikai Posted December 17, 2009 Report Share Posted December 17, 2009 There is no turning back now AC ... You are "Hooked" ma brotha..!!!!!! if you feel you have to use glue for inserts.. I use the "rubber cement" it holds good enough but dry's to a rubbery substance.. that can be taken off easily.. get a case back opener from Watchbitz.. removing the bezel to extract the insert saves wear and tear on the insert.. the rubber cement is like adhesive no need to bind it too tightly with gorilla shtuff.. we've all messed up enough keyless works for you to be in good company.. AC/Lani Link to comment Share on other sites More sharing options...
asciwhite Posted December 17, 2009 Author Report Share Posted December 17, 2009 There is no turning back now AC ... You are "Hooked" ma brotha..!!!!!! if you feel you have to use glue for inserts.. I use the "rubber cement" it holds good enough but dry's to a rubbery substance.. that can be taken off easily.. get a case back opener from Watchbitz.. removing the bezel to extract the insert saves wear and tear on the insert.. the rubber cement is like adhesive no need to bind it too tightly with gorilla shtuff.. we've all messed up enough keyless works for you to be in good company.. AC/Lani Followed Gioarmanis advice on the Gorilla Glue I wish I had the rubber cement advice since I am also into RC cars and use the stuff to glue wheels all the time However... the watch is en route to China to be repaired so when it gets back ill get it off somehow. I used only a few miniscule drops of Gorilla. Thanks guys! Love ya all Link to comment Share on other sites More sharing options...
Pre V Posted January 22, 2010 Report Share Posted January 22, 2010 Hey guys, Great advice on the glue options. I had a pearl dropped out of my insert. Which option should I go with ? Rubber Cement, GS Hypo-cement ??? Appreciate your inputs! Greetz! Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now