ronjohn Posted February 4, 2010 Report Share Posted February 4, 2010 Hi I'm the proud new owner of a nicely modded MBW Great White 1665 - I am in the process of cosmetically aging it as I prefer a more worn look than the previous owner. ( pics coming tonight) The bezel isn't as smooth or easy to turn as I like (it's not totally difficult) but I would like to see if I can make it spin more freely. I did take off the bezel and the ring inside it in order to bleach the bezel. It snapped back on no problem. But it turns stiffer than I would like (it was this way prior to me popping it off). is there are secret to adjusting this at all? It's certainly not broken or anything, but compared to my 5513, it's tighter turning than I would prefer ideally. Relative newbie here. Any ideas are appreciated. Link to comment Share on other sites More sharing options...
FxrAndy Posted February 4, 2010 Report Share Posted February 4, 2010 Try a little drop of oil, for the want of a better oil sewing machine or hair trimmer oil would do the trick Link to comment Share on other sites More sharing options...
aeromatic Posted February 4, 2010 Report Share Posted February 4, 2010 (edited) Hi I'm the proud new owner of a nicely modded MBW Great White 1665 - I am in the process of cosmetically aging it as I prefer a more worn look than the previous owner. ( pics coming tonight) The bezel isn't as smooth or easy to turn as I like (it's not totally difficult) but I would like to see if I can make it spin more freely. I did take off the bezel and the ring inside it in order to bleach the bezel. It snapped back on no problem. But it turns stiffer than I would like (it was this way prior to me popping it off). is there are secret to adjusting this at all? It's certainly not broken or anything, but compared to my 5513, it's tighter turning than I would prefer ideally. Relative newbie here. Any ideas are appreciated. Hello ronjohn i use babe old(johnsons(clear) its clean oil, none greasy and it loves stainless steel afterwards i wipe a little all over the watch and bracelet and polish it gives a nice lusture to the watch and fixes nosy bracelets too use only a small amount if your insert is held by glue (and is not the clip-in type!) i prefer to not remove the bezel and use a cotton bud (ear cleaning)i dip the bud in the baby oil and run it along the beze/ watch case edges and turn it a few time letting it soak in! Edited February 4, 2010 by aeromatic Link to comment Share on other sites More sharing options...
FxrAndy Posted February 4, 2010 Report Share Posted February 4, 2010 Hello ronjohn i use babe old(johnsons(clear) its clean oil, none greasy and it loves stainless steel afterwards i wipe a little all over the watch and bracelet and polish it gives a nice lusture to the watch and fixes nosy bracelets too use only a small amount if your insert is held by glue (and is not the clip-in type!) i prefer to not remove the bezel and use a cotton bud (ear cleaning)i dip the bud in the baby oil and run it along the beze/ watch case edges and turn it a few time letting it soak in! And it wont be bad to your skin!!! Link to comment Share on other sites More sharing options...
aeromatic Posted February 4, 2010 Report Share Posted February 4, 2010 And it wont be bad to your skin!!! thats right or your threads(cloths)! hello fxrandy! Link to comment Share on other sites More sharing options...
FxrAndy Posted February 4, 2010 Report Share Posted February 4, 2010 Hello mate, I wish to retract my statement about baby oil/oils after thinking about a tread a few days ago. Oils will attract grit and become a grinding paste. A dry teflon lube will not, the propellant will evaporate and leave a dry non sticky lubricant behind Link to comment Share on other sites More sharing options...
Nanuq Posted February 4, 2010 Report Share Posted February 4, 2010 The bezel spring on a gen and the MBW is slightly "dished" when you look at it from the side. Make sure the dish is open downward, to match the profile of the crystal retaining ring. Otherwise it's very hard to turn. Link to comment Share on other sites More sharing options...
aeromatic Posted February 4, 2010 Report Share Posted February 4, 2010 Hello mate, I wish to retract my statement about baby oil/oils after thinking about a tread a few days ago. Oils will attract grit and become a grinding paste. A dry teflon lube will not, the propellant will evaporate and leave a dry non sticky lubricant behind never tried that great! i found that johnsons baby oil is very fine and none sticky and none greasy ,i think they do two type the other is greasy! what was the thread name? how about using a little thread grease the copper you use on nuts and bolts that evaporates leaving a lubricant too aeromatic Link to comment Share on other sites More sharing options...
FxrAndy Posted February 4, 2010 Report Share Posted February 4, 2010 you would still have dust and grit sticking to it, copper slip is used in high temp applications like exaust studs and they should not be moving but your bezel should google teflon spray, you get loads of results in your home areas Link to comment Share on other sites More sharing options...
ronjohn Posted February 4, 2010 Author Report Share Posted February 4, 2010 I think I see what you mean - when you say dish open downward - towards the case is it narrower or wider? The bezel spring on a gen and the MBW is slightly "dished" when you look at it from the side. Make sure the dish is open downward, to match the profile of the crystal retaining ring. Otherwise it's very hard to turn. Link to comment Share on other sites More sharing options...
freddy333 Posted February 5, 2010 Report Share Posted February 5, 2010 The bezel spring on a gen and the MBW is slightly "dished" when you look at it from the side. Make sure the dish is open downward, to match the profile of the crystal retaining ring. Otherwise it's very hard to turn. Nanuq is correct. To make the bezel turn easier (it is designed NOT to easily turn), pry the bezel off & flatten the curve of the flat spring washer that sits between the bezel & the case. The flatter the spring washer is, the less tension it places on the underside of the bezel & the freer (easier) it turns. Ideally, the bezel should require a firm press (down) in order to move it. Link to comment Share on other sites More sharing options...
ronjohn Posted February 5, 2010 Author Report Share Posted February 5, 2010 Nanuq is correct. To make the bezel turn easier (it is designed NOT to easily turn), pry the bezel off & flatten the curve of the flat spring washer that sits between the bezel & the case. The flatter the spring washer is, the less tension it places on the underside of the bezel & the freer (easier) it turns. Ideally, the bezel should require a firm press (down) in order to move it. Yes! That was the ticket. Thank you! Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now