hotrodder Posted January 14, 2018 Report Share Posted January 14, 2018 Received a jf 16610 with sh3135 runs great for a couple days but is not auto winding. Is this an easy fix I can do myself. If so what parts do I need. Or who can I send to for reasonable repair i'd rather just pay to fix instead of mailing back to China with hopes of repair. Thanks Sent from my SM-N950U1 using Tapatalk Link to comment Share on other sites More sharing options...
Phener9 Posted January 14, 2018 Report Share Posted January 14, 2018 Hi on my hulk I bought a case back kit off of eBay and found that the rotor screw was loose, I carefully located the rotor into place and tightened the Center screw, job done. I hope it’s as easy and cheap for you. The kit was cheaper than the postage for the watch back to China. Let us know how you get on. Link to comment Share on other sites More sharing options...
SSTEEL Posted January 15, 2018 Report Share Posted January 15, 2018 Hi on my hulk I bought a case back kit off of eBay and found that the rotor screw was loose, I carefully located the rotor into place and tightened the Center screw, job done. I hope it’s as easy and cheap for you. The kit was cheaper than the postage for the watch back to China. Let us know how you get on. The SH3135 doesn't have a central oscillating screw retainer, you maybe referring to an ETA based movement. Received a jf 16610 with sh3135 runs great for a couple days but is not auto winding. Is this an easy fix I can do myself. If so what parts do I need. Or who can I send to for reasonable repair i'd rather just pay to fix instead of mailing back to China with hopes of repair. Thanks Sent from my SM-N950U1 using Tapatalk There have been some reports of the same issue with this movement, which was well known with the SA3135, but now looks to be effecting the SH 3135 movements, there is one gear in the auto wind bridge which is the culprit, many people replace the entire auto bridge for gen, but once again, there have been mixed results in these being compatible. What I suspect is the factories are mixing the batches of SA3135 V2 movements with the SH3135 movements. Easy way to tell a V1 SA3135 to a V2 SA3135 is the sten thickness, the V1 has a very thin tube. 1 Link to comment Share on other sites More sharing options...
mymanmatt Posted January 15, 2018 Report Share Posted January 15, 2018 ssteel is right, no screw on the rotor. Take the back off and have a look. You may see the problem. Good luck I assume you have fully wound it Link to comment Share on other sites More sharing options...
DVNE Posted January 16, 2018 Report Share Posted January 16, 2018 I had a problem and it was a loose screw simple tweak job done. Which screw is it to tighten on a SH3135 (for reference purpose of course) Link to comment Share on other sites More sharing options...
hotrodder Posted January 17, 2018 Author Report Share Posted January 17, 2018 I dont know what its called just checked one by the winding stem and it was loose so tightend it and it was sorted I will check today did you remove movement or just rear cover. ThanksSent from my SM-N950U1 using Tapatalk Link to comment Share on other sites More sharing options...
mymanmatt Posted January 17, 2018 Report Share Posted January 17, 2018 I wouldn't think he needed to remove the movement. That screw was probably the one in the winding bridge. It will affect just about everything to do with the winding, including the self wind. Link to comment Share on other sites More sharing options...
hotrodder Posted January 17, 2018 Author Report Share Posted January 17, 2018 Just rear cover Ok screw turned about 1/4 turn hope that works I'll find out in a few daysThanks againSent from my SM-N950U1 using TapatalkDamn this gets addictaveSent from my SM-N950U1 using Tapatalk Link to comment Share on other sites More sharing options...
RabanJr Posted January 26, 2018 Report Share Posted January 26, 2018 On 1/17/2018 at 11:36 AM, hotrodder said: Ok screw turned about 1/4 turn hope that works I'll find out in a few days Thanks again Sent from my SM-N950U1 using Tapatalk Damn this gets addictave Sent from my SM-N950U1 using Tapatalk Any luck? I had a huge rate fluctuation on my Noob V7 SubC SA3135. It would go from +140 sec/day to -40 sec/day. It was a mess. I opened her up and both screws that hold the movement in place we’re loose. One was about to fall out. I tightened them up and all is well with the world so far. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now