Gigatron Posted July 31, 2007 Report Share Posted July 31, 2007 Hey gang, I received my new bezel insert/pearl today and as I was looking at it, I noticed something about the numbers on the insert. If you look at the pictures, I'll describe what I see First, the noobmariner as is out of the box Next, with the new bezel layed on top And finally, where you can see the diffrences. The numbers and markers are thinner on the new insert. Which insert would be correct for my watch? Technically, it would be easier to just replace the entire bezel insert and pearl instead of just the pearl. Since the original pearl is smaller, it is set lower in the triangle (i.e. closer to the crystal). That means that if I were to enlarge the hole, it would be offset by the distance between it's center and the center I would had to have made if I were drilling a blank insert. The new pearl in the old bezel will not centered correctly or it will have a gap between the pearl and the inside edge of the insert. So, will the new insert work inplace of the original or will it be so completely noticeably wrong, that it would be laughable. I'm holding off making any changes until I hear from you guys. Thanks, Fred Link to comment Share on other sites More sharing options...
gioarmani Posted July 31, 2007 Report Share Posted July 31, 2007 Entire new insert w/ pearl. No question. Link to comment Share on other sites More sharing options...
Gigatron Posted July 31, 2007 Author Report Share Posted July 31, 2007 Well, I did it. The entire bezel insert just popped right off. I used the point of a hobby knife on the outside edge, gave it a little twist and popped it off. The new insert doesn't seem to "pop" back in, so I used some G-S Hypo cement. It has a pinpoint built in applicator so overflow isn't an issue. It's the same glue watch makers use to glue in the crystals, so it dries glass clear and rock hard. I ran a thin bead on the outside edge of the bezel and pressed down on the insert. Hopefully, it holds tight... -Fred Link to comment Share on other sites More sharing options...
HauteHippie Posted July 31, 2007 Report Share Posted July 31, 2007 The thinner numbers are more accurate. And that new pearl is an improvement also. So I would say you've modded the Noobmariner for the better here. Link to comment Share on other sites More sharing options...
cableguy Posted July 31, 2007 Report Share Posted July 31, 2007 should get a jewelryoutlet insert, use the pearl from that watchmaterial insert, and u have the best of both worlds. Link to comment Share on other sites More sharing options...
bklm1234 Posted July 31, 2007 Report Share Posted July 31, 2007 i still think the watchmaterial insert (that's what you got) font a little too thin, that's why i combine a jewelryoutlet insert with the watchmaterial pearl. but it looks good enough to you, don't bother. other people won't notice. -bk Link to comment Share on other sites More sharing options...
Dizzy Posted July 31, 2007 Report Share Posted July 31, 2007 New insert is "more correct" especially the thinner numbers Link to comment Share on other sites More sharing options...
ekhunter Posted July 31, 2007 Report Share Posted July 31, 2007 Entire new insert w/ pearl. No question. Agreed. No doubt about it. Link to comment Share on other sites More sharing options...
eunomians Posted July 31, 2007 Report Share Posted July 31, 2007 Looks good. You should be happy with the results. GS works great, but is does not always dry 'clear', it leaves little residue crystals. But it's one of the best you can get for the job(s). Cheers Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now