GarrettP1 Posted February 26, 2012 Report Share Posted February 26, 2012 I want to drill my lugs on my 1655 Explorer case. Several good "how to" articles are available, but I wasn't clear on the size of the drill bit. Does anyone know? Thanks, Garrett Link to comment Share on other sites More sharing options...
JoeyB Posted February 26, 2012 Report Share Posted February 26, 2012 1.3mm Link to comment Share on other sites More sharing options...
GarrettP1 Posted February 26, 2012 Author Report Share Posted February 26, 2012 Thank you. That was fast! Link to comment Share on other sites More sharing options...
alligoat Posted February 27, 2012 Report Share Posted February 27, 2012 Snap-On #55 works pretty well- PN- DBCE55A. Link to comment Share on other sites More sharing options...
FxrAndy Posted February 27, 2012 Report Share Posted February 27, 2012 I use 1.3mm Link to comment Share on other sites More sharing options...
username here Posted February 28, 2012 Report Share Posted February 28, 2012 is that true of all lug holes? i.e. GMT, sub, Explorer II- all 1.3? Link to comment Share on other sites More sharing options...
alligoat Posted February 28, 2012 Report Share Posted February 28, 2012 I think so and also Explorer I Link to comment Share on other sites More sharing options...
JoeyB Posted February 28, 2012 Report Share Posted February 28, 2012 is that true of all lug holes? i.e. GMT, sub, Explorer II- all 1.3? The Date-Just is smaller, 1mm. Link to comment Share on other sites More sharing options...
Omega Posted February 28, 2012 Report Share Posted February 28, 2012 We had a discussion here about it! I can guarantee, you can NOT push a 1,2mm drill into a gen lughole! I tested it a several times!!! So it is definitly smaller than 1,2mm! Don't ruin your case... But 1,2mm is OK, it's not visible. Lugholes drilled with 1,3mm you can spot easy (even with a nacked eye), because the springbar has not tide fitting! Link to comment Share on other sites More sharing options...
preacher62 Posted February 28, 2012 Report Share Posted February 28, 2012 is that true of all lug holes? i.e. GMT, sub, Explorer II- all 1.3? Everthing that uses the 2mm springbars. Link to comment Share on other sites More sharing options...
FxrAndy Posted February 28, 2012 Report Share Posted February 28, 2012 We had a discussion here about it! I can guarantee, you can NOT push a 1,2mm drill into a gen lughole! I tested it a several times!!! So it is definitly smaller than 1,2mm! Don't ruin your case... But 1,2mm is OK, it's not visible. Lugholes drilled with 1,3mm you can spot easy (even with a nacked eye), because the springbar has not tide fitting! Below in the attached photo is my 1978 gen sub with a bit of 1'2mm steel stuck through the lugs and it is loose. In fact a 1.3mm drill bit fits in but is very tight. If you look at my comparison post between the rep and gen you will see there is almost not visible difference between the gen and the rep in terms of lug hole size on a vintage worn watch and a rep that is supposed to be a vintage watch, they may well have been 1.2 or less when new but they are not new any more To save you the time i will repost a photo here gen is on top by the way Link to comment Share on other sites More sharing options...
Omega Posted February 28, 2012 Report Share Posted February 28, 2012 Andy, I don't want to discuss anymore about it. I own several of gen vintage watches and every month also a lot go thru my hands for overhaul. Use the upper side of the drill and try to put it in the hole. If it works your holes are dead! 1 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now