Mickey Padge Posted November 28, 2006 Report Share Posted November 28, 2006 I found this insert here: http://www.pmwf.com/Watches/WATCHSALES04/W...orRolex1680.htm It cost me $66 delivered, but it looks great, and original vintage dots fit with no problem because it has a 2mm hole! The dot that came with it looked quite good to, but not like the original. Cheers Link to comment Share on other sites More sharing options...
Mickey Padge Posted November 28, 2006 Author Report Share Posted November 28, 2006 Here is a picture after I added my gen dot, sorry for my lack of photo skills I am very happy with it. I am waiting on a white letter dial and then my watch is going to have the dial and crystal upgraded Link to comment Share on other sites More sharing options...
thewightstuff Posted November 28, 2006 Report Share Posted November 28, 2006 looks nice,just out of interest. where did you find the gen dot? Link to comment Share on other sites More sharing options...
Mickey Padge Posted November 28, 2006 Author Report Share Posted November 28, 2006 On ebay! There is a guy on ebay who sells them in pairs every so often I was lucky enough to click the buy it now before anyone else Quick quick someone!!! http://cgi.ebay.co.uk/NOS-Vintage-Rolex-Su...1QQcmdZViewItem Go go! buy buy Link to comment Share on other sites More sharing options...
kingkitesurf Posted November 28, 2006 Report Share Posted November 28, 2006 Repaustria, Please get me one (or two) for that price... I haven't seen a gen one in a while for 70$ (actually never did). Link to comment Share on other sites More sharing options...
Mickey Padge Posted November 28, 2006 Author Report Share Posted November 28, 2006 Mike... I don't want to burst your bubble... but you can often get genuine inserts for the 5513/1665/1680 for as low as 70$ Where, do you have a link please? And no bubble burst because the insert I have is spot on in terms of accuracy Link to comment Share on other sites More sharing options...
Mickey Padge Posted November 28, 2006 Author Report Share Posted November 28, 2006 I am just waiting on the dial now Oliver, as soon as I get it I will let you know Don't forget how far the pound goes against the dollar at the moment, it was cheap really. I thought I would share my search results so others may put together a very accurate insert for their pride and joy Saves buying a load of crap vintage inserts off the bay anyway Cheers Link to comment Share on other sites More sharing options...
Sherrington Posted November 28, 2006 Report Share Posted November 28, 2006 I found this insert here: http://www.pmwf.com/Watches/WATCHSALES04/W...orRolex1680.htm It cost me $66 delivered, but it looks great, and original vintage dots fit with no problem because it has a 2mm hole! The dot that came with it looked quite good to, but not like the original. Cheers You sure the hole size is 2mm and not smaller. The gen dots are 2mm overall so would need a smaller hole, 1.5mm I think offhand? Link to comment Share on other sites More sharing options...
Mickey Padge Posted November 28, 2006 Author Report Share Posted November 28, 2006 You sure the hole size is 2mm and not smaller. The gen dots are 2mm overall so would need a smaller hole, 1.5mm I think offhand? The genuine dot that I got from ebay fits the insert perfectly. A nice solid fit. check out the photo Cheers Link to comment Share on other sites More sharing options...
Mickey Padge Posted November 28, 2006 Author Report Share Posted November 28, 2006 Hmm, I wonder who won the ebay auction? Link to comment Share on other sites More sharing options...
Sherrington Posted November 28, 2006 Report Share Posted November 28, 2006 Hmm, I wonder who won the ebay auction? May come in as a future speculation!!! I bought 6 last time and they are all gone. Link to comment Share on other sites More sharing options...
Mickey Padge Posted November 28, 2006 Author Report Share Posted November 28, 2006 Yeah it's true, you will always be able to sell them All I need now is a bold date overlay, but I can't find one anywhere I have just had a message that my WLSD dial will be posted tomorrow! So close now......... Link to comment Share on other sites More sharing options...
alligoat Posted November 28, 2006 Report Share Posted November 28, 2006 Thanks for the link, Mickey. I happen to think that's a pretty good looking insert even w/ the stock pearl that it comes with. Link to comment Share on other sites More sharing options...
Mickey Padge Posted November 28, 2006 Author Report Share Posted November 28, 2006 Thanks for the link, Mickey. I happen to think that's a pretty good looking insert even w/ the stock pearl that it comes with. Very good point. As un upgrade the insert font is better than the MBW version and the pearl that was in there was better. Sorry I did not take a picture of the pearl before I removed it. 66 bucks and the insert is better than the stock MBW version for sure. Cheers Link to comment Share on other sites More sharing options...
Sherrington Posted November 28, 2006 Report Share Posted November 28, 2006 Very good point. As un upgrade the insert font is better than the MBW version and the pearl that was in there was better. Sorry I did not take a picture of the pearl before I removed it. 66 bucks and the insert is better than the stock MBW version for sure. Cheers Just one question? Does the insert snap into place or have you glued it? Link to comment Share on other sites More sharing options...
Mickey Padge Posted November 28, 2006 Author Report Share Posted November 28, 2006 Just one question? Does the insert snap into place or have you glued it? The insert clicked right into place, no glue. In fact so did the pearl, very firm fit I will add a tiny bit of glue though when I start wearing the watch I think, what would be the best type of glue to use? Could you post a link maybe please? I would be happier knowing that it had a bit of glue securing it Link to comment Share on other sites More sharing options...
Sherrington Posted November 28, 2006 Report Share Posted November 28, 2006 The insert clicked right into place, no glue. In fact so did the pearl, very firm fit I will add a tiny bit of glue though when I start wearing the watch I think, what would be the best type of glue to use? Could you post a link maybe please? I would be happier knowing that it had a bit of glue securing it What I did with my inserts was to clean the back with emery paper to give the glue something to adhere to. I then cleaned both the bezel and back of the insert with some isopropanol cleaning fluid to remove any trace of grease. Then I used a cocktail stick to put tiny spots of araldite rapid at each 5 minute mark on the bezel and snapped the insert into place. Then after cleaning any glue from the front on the insert (there would be none at all if you are careful) I used a cocktail stick again to run a small bead of superglue around the bezel and the insert at the rear. I also glued the dot in as well with araldite to make that ultra secure. Link to comment Share on other sites More sharing options...
Mickey Padge Posted November 28, 2006 Author Report Share Posted November 28, 2006 Thanks for the info, I think I could do that without to many problems Great info indeed Link to comment Share on other sites More sharing options...
thewightstuff Posted November 28, 2006 Report Share Posted November 28, 2006 mickey, thanks for the link. unfortunately i was snoozing and missed it..doh, my gen 5512 could do with a new pearl to fill its hole up. ill keep my eyes peeled though. nice job on the insert though. its very nice indeed and looks good. bet it felt satisfying FYI, if you want to keep the insert in there with something more than a snap fit, i use some clear nail varnish on the underside. holds it great and is easily broken to allow the insert to be removed. using glue is scary, theres always the chance its not going to let it go when you need it to. Link to comment Share on other sites More sharing options...
Sherrington Posted November 28, 2006 Report Share Posted November 28, 2006 mickey, thanks for the link. unfortunately i was snoozing and missed it..doh, my gen 5512 could do with a new pearl to fill its hole up. ill keep my eyes peeled though. Might sell you one of mine when they arrive. If the price is right!!!!!! Link to comment Share on other sites More sharing options...
Mickey Padge Posted November 29, 2006 Author Report Share Posted November 29, 2006 mickey, thanks for the link. unfortunately i was snoozing and missed it..doh, my gen 5512 could do with a new pearl to fill its hole up. ill keep my eyes peeled though. nice job on the insert though. its very nice indeed and looks good. bet it felt satisfying FYI, if you want to keep the insert in there with something more than a snap fit, i use some clear nail varnish on the underside. holds it great and is easily broken to allow the insert to be removed. using glue is scary, theres always the chance its not going to let it go when you need it to. When I saw the insert with the gen dot, I was very pleased with the result to say the least I waited until I received the insert and was sure the dot fit OK before I posted the link. I did not want people to buy the inserts until I was sure they were the correct size and fit etc..... Now we have a good source for vintage inserts and we can buy gen dots, that is if he has any left Thanks for the tip on securing the insert, I will go with a glue that is not so strong I think Link to comment Share on other sites More sharing options...
thewightstuff Posted November 29, 2006 Report Share Posted November 29, 2006 Might sell you one of mine when they arrive. If the price is right!!!!!! feel free to PM me when they arrive and let me know your thoughts Link to comment Share on other sites More sharing options...
Sir-Lancelot Posted November 29, 2006 Report Share Posted November 29, 2006 "All I need now is a bold date overlay, but I can't find one anywhere " My friend, A member PM me the link to www.cubic-works.com and they do have the bold date wheels you want. The problem is, I paypal him the money October 10th, and NOTHING. No overlay, and not one single reply to my mail from them. If anyone has one of these or can send me to a different supplier, i would appreciate it very much. I would almost try to buy again from cubic-works. Just because i cant find anywhee else and i need one of these. Link to comment Share on other sites More sharing options...
Mickey Padge Posted November 30, 2006 Author Report Share Posted November 30, 2006 I contacted the shop that sold me the insert and gave them a description of the date overlay I needed. I sent a picture too and mentioned it must be a clockwise date change. They replied they could get that part for me and that it would be $17 delvered! I will wait and see what they send before I get to carried away Rest assured I will post pictures regardless, as soon as it arrives Cheers Link to comment Share on other sites More sharing options...
eunomians Posted November 30, 2006 Report Share Posted November 30, 2006 Used to be able to get OEM inserts for $35 down the street from me. Not anymore since they liquidated their Rolex stock. Ahhh, the good ol' days. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now