danielv2000 Posted August 16, 2013 Report Share Posted August 16, 2013 On the classic SSDs (not the BP or superlumed Ultimates) is there a way to remove the bezel without damaging it or the insert? I don't think these pop out like gens do, correct? Thank you for the help!! Link to comment Share on other sites More sharing options...
woof* Posted August 16, 2013 Report Share Posted August 16, 2013 Bad idea to remove bezel probably. Could get bent for your effort, and most likely will. Some of the modders out there have done it though. You might ask Bonesy or Jmb depending on location. I have personally slightly bent one, and worse yet after straightning the bezel...got stuck frozen when I put it back on. The insert is easy, heat the insert with a hair dryer or soldering iron, use an x-acto knife with fresh sharp blade to lift edge of insert up. If you don't mind destroying the pearl, use a dental pick to pry the pearl out, then lift up from the hole where the pearl was. Link to comment Share on other sites More sharing options...
kbh Posted August 16, 2013 Report Share Posted August 16, 2013 I've had mine off and I don't remember it being particularly difficult to get off. Loosen with razor blade and then used a watch knife. Try to loosen it and twist the bezel a little. Link to comment Share on other sites More sharing options...
Ephry73 Posted August 16, 2013 Report Share Posted August 16, 2013 If it is an old SSD V2/1 case the bezel is not as detrimental to take off. Tape the lugs and go around until it pops up. On the BPs is a different story. E 1 Link to comment Share on other sites More sharing options...
woof* Posted August 16, 2013 Report Share Posted August 16, 2013 Good info, I didn't know that about the SSD. Link to comment Share on other sites More sharing options...
Ephry73 Posted August 16, 2013 Report Share Posted August 16, 2013 Another pro on the lovely SSD Link to comment Share on other sites More sharing options...
netniet Posted August 16, 2013 Report Share Posted August 16, 2013 Nice, just in time. I was about to replace the insert of my v2 myself. Link to comment Share on other sites More sharing options...
woof* Posted August 16, 2013 Report Share Posted August 16, 2013 I'm considering selling mine Link to comment Share on other sites More sharing options...
danielv2000 Posted August 17, 2013 Author Report Share Posted August 17, 2013 Hey, thanks for the info y'all! Link to comment Share on other sites More sharing options...
marqtz Posted September 30, 2017 Report Share Posted September 30, 2017 On the classic SSDs (not the BP or superlumed Ultimates) is there a way to remove the bezel without damaging it or the insert? I don't think these pop out like gens do, correct?Thank you for the help!!Is it a Z series? Link to comment Share on other sites More sharing options...
danielv2000 Posted September 30, 2017 Author Report Share Posted September 30, 2017 3 hours ago, marqtz said: On 8/16/2013 at 10:31 AM, danielv2000 said: On the classic SSDs (not the BP or superlumed Ultimates) is there a way to remove the bezel without damaging it or the insert? I don't think these pop out like gens do, correct? Thank you for the help!! Is it a Z series? That's a trip down memory lane! If memory serves me, it is one of the famous z series! 1 Link to comment Share on other sites More sharing options...
alligoat Posted October 1, 2017 Report Share Posted October 1, 2017 Z539117 if I'm not mistaken Link to comment Share on other sites More sharing options...
marqtz Posted October 1, 2017 Report Share Posted October 1, 2017 Z539117 if I'm not mistakenMine too Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now