Aero_Dave Posted July 3, 2013 Author Report Posted July 3, 2013 Whoo Hoo. Can't wait Whoopy's. Dave...
whoopy12 Posted July 10, 2013 Report Posted July 10, 2013 UPDATE #7 Dial test printing has begun! The 1665 drsd was the first design tested on a few scrap dials today. The ink will be raised in the final product (as per gen), but just a TAD less than the current level shown here. The reason I decided to replicate the 1665 in the first place was because I loved the aesthetic of the crown. Almost every aftermarket dial I've seen neglects existing nuances. Below are three pictures of the test print dial, and a gen coronet for comparison
CptTripps Posted July 10, 2013 Report Posted July 10, 2013 REALLY wish you could do these on Singer blanks so I could use mine with a gen movement.
whoopy12 Posted July 10, 2013 Report Posted July 10, 2013 REALLY wish you could do these on Singer blanks so I could use mine with a gen movement. I'll be using mine on a gen movement - going to reposition/solder the feet
wiesn089 Posted July 11, 2013 Report Posted July 11, 2013 Wow, that 1665 dial looks great, any full shots? Damn, I couldn't decide between a 1680 and a 1665 DRSD for a slim case PP, I hope the 1680 will turn out equally amazing. Any chances for another Singer blanks run, when these are done? Soldering feet might damage the print and I don't think I'll be content with a ETA based mf franken when my dial looks that good. 1
CptTripps Posted July 11, 2013 Report Posted July 11, 2013 Any chances for another Singer blanks run, when these are done? Soldering feet might damage the print and I don't think I'll be content with a ETA based mf franken when my dial looks that good. +1
dieselpower Posted July 15, 2013 Report Posted July 15, 2013 Received my strap by the way - thanks Whoopy good luck with the dials all looking great.
CptTripps Posted July 16, 2013 Report Posted July 16, 2013 I'll be using mine on a gen movement - going to reposition/solder the feet If you can make it work, I'd be happy to pay you to make mine fit a gen movement.
whoopy12 Posted July 17, 2013 Report Posted July 17, 2013 If you can make it work, I'd be happy to pay you to make mine fit a gen movement. I think I'll leave it to a modder, but it actually doesn't look too difficult: http://dialrestore.com/ UPDATE #8 Dials have been printed - I was told about 10% had small defects in the printing, so these will need to be dunked in alcohol (to remove the base layer of matte black paint), repainted, and padprinted - again. Once all of the reprinted dials pass QC, I will make the 2nd payment and the dials will be shipped to me. As a side note: While I definitely think the wait will be worth it, it's killing me! All my phong franken build needs is that MK2 dial! - Whoop
Akira Posted July 19, 2013 Report Posted July 19, 2013 Whoppy, Do you think you'll make a second run afterall?
docthor Posted July 19, 2013 Report Posted July 19, 2013 Hope so...I need a 1680 mk3 Sent from my wooden drums using Tupperware
southernsurfer Posted July 20, 2013 Report Posted July 20, 2013 Hope so...I need a 1680 mk3 Oh That would be Great! I'd like to second this
fitch Posted July 20, 2013 Report Posted July 20, 2013 Yes! I'm sorry to see I missed out on this (been away for a while) but if possible I would like to purchase/order 5. 1680 red mk 3 (26.5mm) $180 6. 1665 drsd mk 2 (26.5mm) $180
whoopy12 Posted July 21, 2013 Report Posted July 21, 2013 Whoppy, Do you think you'll make a second run afterall? As mentioned earlier in this thread, I'll only be producing this limited run. Because I needed to come close to the minimum order quantity for the dial factory, more dials ARE available. The original pre-order list was created JUST to cover the cost of printing this order. Short answer: If you need a dial, pm me and I'll let you know if the model specified is available. Hope so...I need a 1680 mk3 Sent from my wooden drums using Tupperware Pm me Yes! I'm sorry to see I missed out on this (been away for a while) but if possible I would like to purchase/order 5. 1680 red mk 3 (26.5mm) $180 6. 1665 drsd mk 2 (26.5mm) $180 Pm me
Akira Posted July 21, 2013 Report Posted July 21, 2013 As mentioned earlier in this thread, I'll only be producing this limited run. Because I needed to come close to the minimum order quantity for the dial factory, more dials ARE available. The original pre-order list was created JUST to cover the cost of printing this order. Short answer: If you need a dial, pm me and I'll let you know if the model specified is available. PM sent.
whoopy12 Posted July 22, 2013 Report Posted July 22, 2013 UPDATE #9 Just received more pictures! THESE LOOK GREAT As mentioned earlier, after the misprints are reprinted, I will make the second payment, and the dials will be shipped. 1
Sparkal Posted July 22, 2013 Report Posted July 22, 2013 Wow.those look insanely good.Nice work mate. Gutted I have missed this threadsent from my smart phone whilst sitting on the toilet
whoopy12 Posted July 22, 2013 Report Posted July 22, 2013 Forgot the last picture! Comex logo is printed as per gen: black ink over white No other aftermarket comex dial is printed this way 1
rower Posted July 25, 2013 Report Posted July 25, 2013 So excited to see these! I'm glad that I jumped on these right away.
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now