vvvlllooo Posted July 2, 2018 Report Share Posted July 2, 2018 V9 SEL and Bezel comparisons (ARF bracelet included and installed on the V9) So, there is a lot of hype on the V9 Noob that just came out. There were also a lot of concerns with the SELs. This write up compares the V9 to a Gen, the new bezel construction, and clasps. I also had an ARF bracelet I had ordered and installed on the V9 to show you how it would look with it on. I will tell you that the stock V9 Noob bracelet felt so much better and solid between the two. Both are made from 904L steel. Although I feel both are made very well I may have to modify, a little, of the ARF to make it sit nice and right. I will post in the future once I this is done but at this time, right out of the box, the Noob sits perfectly as it was made for the watch. I think both options are very good if you happen to go this route and there is no wrong answer, you only feel it in the pocket book. Off to the Picts..... V9 vs Gen V9 With ARF Bracelet Link to comment Share on other sites More sharing options...
marqtz Posted July 2, 2018 Report Share Posted July 2, 2018 Great comparison. Thanks for sharing! Link to comment Share on other sites More sharing options...
Sogeha Posted July 2, 2018 Report Share Posted July 2, 2018 Really great to see this in detail, thanks for posting Link to comment Share on other sites More sharing options...
vvvlllooo Posted July 2, 2018 Author Report Share Posted July 2, 2018 thanks guys! Link to comment Share on other sites More sharing options...
mrsoundman Posted July 2, 2018 Report Share Posted July 2, 2018 Just wanted to reiterate that it's great to see this level of comparison. Thanks brother! Link to comment Share on other sites More sharing options...
vvvlllooo Posted July 2, 2018 Author Report Share Posted July 2, 2018 Thank you...to be clear the ARF bracelet does increase the recession of the SEL's. You would have to modify it a little for it not to wobble around, which looks easy enough to do. Link to comment Share on other sites More sharing options...
cheld Posted July 2, 2018 Report Share Posted July 2, 2018 ARF clasp has a more accurate coronet and scrolls, but the font alignment is terrible (W in SWISS, OL in ROLEX). Link to comment Share on other sites More sharing options...
WhittyMorning Posted July 2, 2018 Report Share Posted July 2, 2018 Man! That is close!!!! Do you think the ARF or V9 comes closer as far as over all? Link to comment Share on other sites More sharing options...
vvvlllooo Posted July 2, 2018 Author Report Share Posted July 2, 2018 (edited) 5 minutes ago, WhittyMorning said: Man! That is close!!!! Do you think the ARF or V9 comes closer as far as over all? The noob feels and looks closer to GEN as far as the SEL is concerned. Again, the stock bracelet was made for the watch. ARF will be just sit a tad lower...those who had ordered the later Noob v9, complained about how flush they were starting to look and so a fix would be the ARF bracelet..as it does sit lower than the v9. You wouldn't have to do too much to the ARF bracelet to make it look nice, there's a write up on RWI..springbar that could possibly just do the trick. I even put my GEN bracelet on the v9 and the SEL's looked pretty close to the v9. I also used the stock 2mm spring bar so it has little play but to answer your question, if you get a nice SEL v9...it will already do the trick. Edited July 2, 2018 by vvvlllooo Link to comment Share on other sites More sharing options...
jamestan119 Posted July 13, 2018 Report Share Posted July 13, 2018 do you mind the compare the rehaut in the inner circle of gen ar and noob? some said ar engrave is close to the original Link to comment Share on other sites More sharing options...
automatico Posted July 13, 2018 Report Share Posted July 13, 2018 Another bracelet comparison: https://www.tapatalk.com/groups/vintagerolexforum/new-fake-bracelets-t244233.html With a few exceptions it looks like the replica holds its own. Then there is the price...$700 or more vs $125 or so. Link to comment Share on other sites More sharing options...
kgvertu Posted July 31, 2018 Report Share Posted July 31, 2018 Thanks for the comparison shots. Amazing. Thing that always caught my eye, how the engraving white on be bezel looks so clean but on the rep it always looks dirty. It's quite a big flaw when you're that close! Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now