irolexu Posted January 2, 2013 Report Share Posted January 2, 2013 I've been wearing my super franken Sean 16610 and the bezel assembly is completely gen and was wondering if finding a slightly thicker spacer will tighten things up? Is there different thicknesses for the metal washer if so where can I get one? Link to comment Share on other sites More sharing options...
irolexu Posted January 2, 2013 Author Report Share Posted January 2, 2013 Seems like the bezel could be a little tighter after comparing to an all gen 16610 Link to comment Share on other sites More sharing options...
freddy333 Posted January 2, 2013 Report Share Posted January 2, 2013 Have you replaced the crystal with a genuine crystal? The way a bezel fits on a Rolex has to do with the crystal. After market crystals tend to be slightly thinner/smaller, which allows for more play in the bezel's fit on the case. Link to comment Share on other sites More sharing options...
irolexu Posted January 2, 2013 Author Report Share Posted January 2, 2013 Yup it's a gen AR crystal Link to comment Share on other sites More sharing options...
freddy333 Posted January 2, 2013 Report Share Posted January 2, 2013 I assume by 'AR crystal' you mean the cyclops has an AR coating, not the entire crystal. Correct? Link to comment Share on other sites More sharing options...
alligoat Posted January 2, 2013 Report Share Posted January 2, 2013 The old trick that used to work on the 5512/3s and 1680s was to put a bend or kink in the flat washer. That would create the necesaary friction to slow down the bezel- might try it on the 16610. All my problems w/ the 16610 bezel assembly have been a case of too tight! Link to comment Share on other sites More sharing options...
gavidoc Posted January 3, 2013 Report Share Posted January 3, 2013 (edited) The old trick that used to work on the 5512/3s and 1680s was to put a bend or kink in the flat washer. That would create the necesaary friction to slow down the bezel- might try it on the 16610. All my problems w/ the 16610 bezel assembly have been a case of too tight! same for me. I went through a total of 7 gen bezels (including my original) before I was able to settle on the 3 I needed to make insert changing easier on my 16800. 4 of the 7 were too tight. Was the retaining ring and the bezel obtained as a set? If not, the retaining ring could have more wear on it then the interior surfaces of the bezel. Only way to fix this is to bend the click spring out further to apply greater pressure on the bezel. This in turn will tighten it up but will also result in making it harder to turn the entire assembly. Edited January 3, 2013 by gavidoc Link to comment Share on other sites More sharing options...
mymanmatt Posted January 5, 2013 Report Share Posted January 5, 2013 I think your picking your watch too much. Yours turns like it should, if a gen is any tighter, then it has been worked on and the gen is not correct Link to comment Share on other sites More sharing options...
panerai153 Posted January 5, 2013 Report Share Posted January 5, 2013 Sometimes we get a little too anal for our own good. I'm speaking from experience, because it hits me all the time. I get hung up on one small detail, and it worries me to death. I'm not talking about flaws that you can see from 20 feet away, but little things that no one else would notice unless you pointed them out. One of our problems is we focus on the little "nit picking" things with our reps, but what we don't see are the differences in genuines as well. I would bet that if you picked up 10 genuine subs, just like yours, you would find a fair difference in the pressure needed to turn the bezel. Link to comment Share on other sites More sharing options...
Rolexman Posted January 20, 2013 Report Share Posted January 20, 2013 Have you replaced the crystal with a genuine crystal? The way a bezel fits on a Rolex has to do with the crystal. After market crystals tend to be slightly thinner/smaller, which allows for more play in the bezel's fit on the case. Could you elaborate on that? I thought the retaining ring combined with the washer and click provide the tension to the bezel? Link to comment Share on other sites More sharing options...
correctime Posted January 22, 2013 Report Share Posted January 22, 2013 (edited) That's right. The retaining ring, flat tension washer and click spring is what gives the gen bezel assembly it's "precision". As already mentioned it's best to keep retaining and bezel rings paired from the beginning (when possible) Tweeking the flat tension washer will add some stiffness as will tweeking the tip of the click sping (unless it's a gen clicker) And of course changing/renewing the flat tension washer will likely give the added stiffness you're after...often that'll make it too tight until it sort of "arcs" to the slight wear already in the retainer and bezel ring. NOTE: the only variation in the thickness of gen flat tension washers for the 16800/16610 bezel assemblies that I'm aware of is age and wear Edited January 22, 2013 by correctime Link to comment Share on other sites More sharing options...
irolexu Posted January 22, 2013 Author Report Share Posted January 22, 2013 I got it tightened up guys. A simple bend in the washer tightened it up Link to comment Share on other sites More sharing options...
Ephry73 Posted January 22, 2013 Report Share Posted January 22, 2013 All of the used spring washers I have seen have at least three bends in them. Glad you got it sorted Link to comment Share on other sites More sharing options...
irolexu Posted January 23, 2013 Author Report Share Posted January 23, 2013 Ya it was getting annoying when my pearl would slowly sneek around the corner everyday Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now