HaydenM Posted October 3, 2015 Report Share Posted October 3, 2015 Hi All,Anybody know a good source for a gen-like caseback for a cartel 1675 unlike the bubble like back that comes with it?Thanks in advance,HaydenM Link to comment Share on other sites More sharing options...
droptopman Posted October 3, 2015 Report Share Posted October 3, 2015 Hi All,Anybody know a good source for a gen-like caseback for a cartel 1675 unlike the bubble like back that comes with it?Thanks in advance,HaydenMIf I remember we used a 5513 CB from rafflestimes. Much flatter. Watch is out being serviced or I would get you some pics. Check Rolex Addicts area over on Repgeek he has a thread with this info. Link to comment Share on other sites More sharing options...
jmb Posted October 3, 2015 Report Share Posted October 3, 2015 If it's supposed to be flat in the middle it could be milled, and while being milled it could have a PanAm logo added... 1 Link to comment Share on other sites More sharing options...
ceejay Posted October 4, 2015 Report Share Posted October 4, 2015 Here you go... http://rafflestime.com/milsub-watch-case-back/ Link to comment Share on other sites More sharing options...
HaydenM Posted October 4, 2015 Author Report Share Posted October 4, 2015 Here you go... http://rafflestime.com/milsub-watch-case-back/Thanks for that, wasn't certain which case back. Places the order with them Link to comment Share on other sites More sharing options...
jmb Posted October 5, 2015 Report Share Posted October 5, 2015 If these are anything like the HR case-backs they are extremely thin. Link to comment Share on other sites More sharing options...
Nanuq Posted October 5, 2015 Report Share Posted October 5, 2015 Roger that, I can dent the caseback on my gen 1675 with my thumb. Link to comment Share on other sites More sharing options...
ceejay Posted October 5, 2015 Report Share Posted October 5, 2015 Unless he's changed supplier in the last year or so then these are not thin enough to dent without a fair amount of force.I have just tried on mine Link to comment Share on other sites More sharing options...
Nanuq Posted October 5, 2015 Report Share Posted October 5, 2015 Mister Wussy Thumbs! (neener neener neener) 1 Link to comment Share on other sites More sharing options...
jmb Posted October 5, 2015 Report Share Posted October 5, 2015 C'mon, Mr. Freeze, he does have a squirrel humpin' his ear for an excuse! I didn't realize a gen was thin. I have engraved a couple of the HR case backs and they were almost a no-go due to being so thin... 1 Link to comment Share on other sites More sharing options...
Nanuq Posted October 5, 2015 Report Share Posted October 5, 2015 I actually dented mine pretty badly using a press to seat a retaining ring. I got it sorta flat again but probably need to send it to you so you can use a brass squared off blank to press it REALLY flat again. Link to comment Share on other sites More sharing options...
jmb Posted October 6, 2015 Report Share Posted October 6, 2015 I've got a 20 ton press so it could go one of two ways! I've turned Delrin dies that put the pressure on the edge of the case-back so don't ned to worry about denting anything... Link to comment Share on other sites More sharing options...
HaydenM Posted October 6, 2015 Author Report Share Posted October 6, 2015 Well I've put in my order and I'll get back to you all with the current quality when it arrives. Link to comment Share on other sites More sharing options...
Nanuq Posted October 6, 2015 Report Share Posted October 6, 2015 I've got a 20 ton press so it could go one of two ways! Ohhhhhhh baby! Now you're teasing me.! Link to comment Share on other sites More sharing options...
automatico Posted October 6, 2015 Report Share Posted October 6, 2015 "Roger that, I can dent the case back on my gen 1675 with my thumb."The average 1970s 1675 case back is around .9mm thick in the center depending on wear. Just now measured a few repsub etc case backs...one new 'shitinerand' was .9mm, , another was .74mm. An unsigned '21 jewel' sub case back from a guy called 'Cal' 15 or 17 years ago was 1.15mm, this case is built like a Sherman tank with a hole in the case top at 12 with a coil spring and plunger that ratchets against notches machined in the spring wire mounted rotating bezel. These things are Nanuq proof. Maybe.Checked a 10+ year old swisseta 'shitinerand' yacht-molester and it was .84mm. A sapphire crystal Exp II swisseta case from 'River' 12 or 14 years ago was 1.55mm thick. An MBK 'polex' 5513 was 1.75mm, and a DW 5513 was 1.15mm. The case back with the best lettering in the assortment above is the DW.A two year old 5513 case back from Yuki is 1.2mm thick and has the best lettering of the bunch....but everyone knows 'shitinerands' are still the absolute best because they are hand made by Elves in the small swiss alps town known as Gelena. 2 Link to comment Share on other sites More sharing options...
Nanuq Posted October 6, 2015 Report Share Posted October 6, 2015 Elves.... with attitude! Link to comment Share on other sites More sharing options...
HaydenM Posted October 15, 2015 Author Report Share Posted October 15, 2015 UPDATE:Got the delivery today and changed out the caseback from the normal bubble caseback to thisAlso for any interested while I was at it decided to change from pepsi to black bezel insert:From:To: Link to comment Share on other sites More sharing options...
ogladio Posted October 15, 2015 Report Share Posted October 15, 2015 Looking good! Link to comment Share on other sites More sharing options...
Beachcomber Posted October 15, 2015 Report Share Posted October 15, 2015 I love the black bezel on the 1675, beautiful Sent from my iPhone using Tapatalk Link to comment Share on other sites More sharing options...
HaydenM Posted October 16, 2015 Author Report Share Posted October 16, 2015 I love the black bezel on the 1675, beautifulAs do I, it wears a bit more understated which I love. It's wearing quite a bit more comfortable with the new caseback. Only things left in the near future for this watch is to fix the hands (the GMT hand is off by about half an hour) and then figure out how to change the crystal. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now