Jump to content
When you buy through links on our site, we may earn an affiliate commission.
  • Current Donation Goals

How to make a better cannon pinion for a Panerai 7750 movement.


sander

Recommended Posts

As we already discussed in milesd topic and as Sul said, we don't want to spoil his wonderful topic of his new watch, so I decided to write a new one.

For me one of the biggest tells with a 7750 in a panerai, is the high cannon pinion. The problem is caused by the hole in the pinion which is normally needed for the chrono hand. To close the hole, they made a nickel plated brass cap which sits on top of the pinion.

post-9210-073520600 1283342997.jpg

If you take off the cap, the pinion is the right height but then you will end up with a hole in the middle. If you sand the cap down, you will notice that you can't sand it enough (because no cap at all is the right height ;))

and it will also turns yellow because you remove the nickel. To solve this problem, I have modded the pinion with a new stainless steel cap.

First I removed the standard cap and cut off the piece that normally holds the hand.Then I made a new cap out of a stainless steel rod. (it was actually a 1,26 mm nail :D )

I made it a tight fit so that the cap is pressed in place. (see drawing)

post-9210-079407300 1283343001.jpg

You also have to cut a little piece of the brass rod of the main plate. Because the cap sits lower, you cannot install the pinion correctly over the brass rod. It's not a problem to cut it down a little because this rod holds the jewel for the chrono seconds hand, which is not needed in this case. If you cut off just a little there is enough rod left to support the pinion.

post-9210-056532500 1283343761.jpg

It's a pretty tough mod because of the size it's difficult to work on.

Another issue is that you will have to completely service the movement because you have to cut a piece off from the brass rod of the main plate.

Since I don't believe it's possible to do this without getting filings into your movement it's better to give it a service as well.

Actually, a service is always welcome :thumbsupsmileyanim:

post-9210-062419400 1283343007.jpg

post-9210-084497800 1283343015.jpg

post-9210-097390500 1283343742.jpg

post-9210-066680200 1283343750.jpg

post-9210-041087300 1283343758.jpg

Cheers!

Sander

Link to comment
Share on other sites

So, you didn't have to cut the pinion itself, just replace one cap with another - did I get this right ?

Fantastic work BTW, it is bothering me for long time, but making new cap is currently beyond my capabilities :wounded1:

If you happen to make extra cap or two, and decide to sell them, let me know ;)

regards

Link to comment
Share on other sites

So, you didn't have to cut the pinion itself, just replace one cap with another - did I get this right ?

Fantastic work BTW, it is bothering me for long time, but making new cap is currently beyond my capabilities :wounded1:

If you happen to make extra cap or two, and decide to sell them, let me know ;)

regards

No you do have to cut the pinion as well. (look at the drawing)

you cut it down till the dotted line.

Link to comment
Share on other sites

Thanks for all the comments.

Since my wife really don't understand what the fun is creating a piece which is almost too small to see, I really appreciate it that you guy's do! :thumbsupsmileyanim:

I received some questions how I actually cut the cap.

Here you go:

First I put the nail (1.26mm thick) in the Dremel and used a needle file covered with fine (800 and 1200) sandpaper to shape it down to 1.20mm

Then I put the 1.20mm part of the nail into the Dremel and shaped the other end down to 0.70mm

Now you have a nail (total length about 0.50 cm.) which is 1.2mm on one half and 0.70mm on the other half.

The next thing was to shorten the 0.70mm side down to 0.40mm. After that I installed it into the cannon pin.

Now I had a cannon pin with a very tall cap. The next step was to cut down the cap to the proper length and polish it.

I made some drawings to clarify it.

post-9210-027304200 1283373266.jpg

post-9210-001775900 1283373273.jpg

Link to comment
Share on other sites

Thanks. Don't have the skills and tools for this, but my local watch smith does. Will use it on my fully modded pam252 and 156 later. Thanks so much.

Have to say, once in a while a very rare and quality wise good informative modding thread is started. This is one of them. :thumbsupsmileyanim:

Link to comment
Share on other sites

Thanks. Don't have the skills and tools for this, but my local watch smith does. Will use it on my fully modded pam252 and 156 later. Thanks so much.

Have to say, once in a while a very rare and quality wise good informative modding thread is started. This is one of them. :thumbsupsmileyanim:

bedankt maat maar nu naar bed!

Link to comment
Share on other sites

Ok, first of all, coming up with the mod itself was just pure genius! I don't own a 7750 powered PAM, nor will I at anytime. However, as an engineer & tinkerer, I can definitely appreciate the ingenuity put forth in coming up with this mod. I applaud your skills Sander!

Secondly, to take the time to do such an incredibly detailed outline of exactly how you did it, including graphical references, is just awe inspiring! A huge kudos to you!! :clapping::thumbsupsmileyanim::1a:

Link to comment
Share on other sites

Great job Sander. My only question regarding the detailed step by step you gave (thanks for that by the way) is in the final step. What method did you use cut down the tall cap once attached to the cannon? I assume something with the dremmel again.

Amazing work!

Link to comment
Share on other sites

Great job Sander. My only question regarding the detailed step by step you gave (thanks for that by the way) is in the final step. What method did you use cut down the tall cap once attached to the cannon? I assume something with the dremmel again.

Amazing work!

Started with the Dremel

After that the needle file

After that the needle file covered with 800 sandpaper

After that the needle file covered with 1200 sandpaper

Finally polishing on the buffing machine.

:D

Link to comment
Share on other sites

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...
Please Sign In or Sign Up