Jump to content
When you buy through links on our site, we may earn an affiliate commission.
  • Current Donation Goals

Still no aftermarket 702 crown tube options?


bones

Recommended Posts

Phong has aftermarket 702 tubes!

 

That's new news. Last time I checked , he had 700's, not 702's. When did you see this?

 

Btw, I contacted ebay seller jewelerstools yesterday and he told me he had a used and usable 702 tube for 100$

Link to comment
Share on other sites

That's new news. Last time I checked , he had 700's, not 702's. When did you see this?

 

Btw, I contacted ebay seller jewelerstools yesterday and he told me he had a used and usable 702 tube for 100$

 

I emailed him a couple months ago. Didn't end up getting them since I found a nice deal on a gen crown + tube :D

Link to comment
Share on other sites

Tom

The early ( 5512/13/1680/1665 etc) subs started with 702's from the factory. Later on when serviced in the 80's and forward.... they were replaced with 703's. I don't know exactly when, but at some point they built the last subs with 703's from the factory.

Either crown is "accurate". I like the 702's better because they are thinner, and with some cases look a lot better.

My 5512 with 702

null_zpsa3f21b15.jpg

Same watch but service insert.

c7c792ce.jpg

  • Like 1
Link to comment
Share on other sites

  • 4 weeks later...

I have found a source in the CONUS for the elusive aftermarket 24-7020 tubes. But before I post a link the seller asked for me to wait until he has better pictures to post on his site. The quality looks there. And I did a mock up with the gen 702, and it threaded like butter. I think we may have a winner here guys.

Sent Via Tapatalk HD

Link to comment
Share on other sites

Hi folks...I don't want to hijack this thread...but for those of you guys really needing a gen 7020 tube...I will have several NOS tubes coming in the next few weeks.....for those of you that can't wait.phong has an aftermarket tube/crown set that are acceptable.However, the tubes/crowns have weak threads and are prone to wearing out prematurely.The base metal used is less than ideal.the tubes also braek in the cases if you try to torque them too tight....

j

Link to comment
Share on other sites

I am getting a little confused here

The various pictures above of 702 crowns all have the correct deep, tall coronet, but not all tall coronet crowns are 702 s are they?

I understood the 702 had the tall coronet and thinner sectiona as shown also above.

Arent the wrapped, tall coronet triplocks from the late 70's the early 703s?

If not, then 702s as described here fit 703 tubes and seal up to 7 and 10 atm?

I have one installed on my 1665 mbw now. I have even had one installed on a TC 16610 for some time cos the TC crown was playing up? Both were pressure tested to 10 atm.

I always assumed these were early wrapped, tall coronet 703s?

Can anyone clarify this - I expect freddy or Ubi will know?

My 1665 is featured in a live thread from me a few posts below - which crown is that?

Link to comment
Share on other sites

Mapman: early 703s look like 702s.  Easiest way to tell the difference is to place the crown coronet-side down.  

 

On the 702, the threads run all the way to the top. 

http://www.chrono-shop.net/img/p/953-5005-thickbox.jpg

 

On the 703, they don't.

http://img.auctiva.com/imgdata/1/4/9/0/1/4/9/webimg/572089904_o.jpg

 

 

Looking at the tubes, when installed the 7020 has threads near the case, but is then smooth:

http://www.chrono-shop.net/img/p/3042-22122-thickbox.jpg

 

For the 7030, the tube has a smooth spot near the case to fit a gasket, and then is threaded:

http://www.jewelerssupplies.com/media/R7030.jpg

  • Like 2
Link to comment
Share on other sites

Mapman: early 703s look like 702s.  Easiest way to tell the difference is to place the crown coronet-side down.  

 

On the 702, the threads run all the way to the top. 

http://www.chrono-shop.net/img/p/953-5005-thickbox.jpg

 

On the 703, they don't.

http://img.auctiva.com/imgdata/1/4/9/0/1/4/9/webimg/572089904_o.jpg

 

 

Looking at the tubes, when installed the 7020 has threads near the case, but is then smooth:

http://www.chrono-shop.net/img/p/3042-22122-thickbox.jpg

 

For the 7030, the tube has a smooth spot near the case to fit a gasket, and then is threaded:

http://www.jewelerssupplies.com/media/R7030.jpg

Excellent, many thanks.

So as I thought, I have a bunch of early 703's that fit on a standard 703 tube, that explains it!

Thanks again for the education and links. :-)

Link to comment
Share on other sites

I am making a rolex 702 crown and tube replacement, crown will be ready soon :)

Super ! Im enjoying my two brevet crowns !!!!!  

Link to comment
Share on other sites

Only because of this thread, I realized that I'm a 702 crown hoarder.... :help:

 

 

file_zps1b347e0f.jpg

 

file_zpse2b4c8ba.jpg

 

file_zps8380694c.jpg

 

 

 

:bounce:

I want Three !!! for starters !!!!!

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
×
×
  • Create New...
Please Sign In or Sign Up