Ronin

Hollow Coffee Stirrer. Like a straw--- dip, finger over top, dump. (Any small hollow tube, use like a straw) Ideally, get a syringe though.

Thanks guys. I am really digging the Yobokies AR Crystal on this with the slight dome. It really makes this a unique Sammy now. And sapphire gives it a higher quality appearance to boot. In the winder BEFORE, it was just there minding its own business. Now, after the clean up and crystal swap it screams 'check me out'.

@HikeUSA, I love that PVD PAM of yours!

Food

Correction, it will pass the earth at 28,800 miles, and all mechanical watches with a 28,800 beat will burn up...

It is not uncommon to extract 15xx movements from inexpensive older DateJusts to use in 1680, 1665, etc, projects. Then either convert the old DJ to ETA power, or sell off the case/dial etc for a few bucks.

Now those are some serious levers. I converted to levers since I never felt the typical presto pullers gave me a sense of confidence or feel. I only use a Presto for the Center Seconds hand these days, and levers for everything else.

As many of you know I am a huge Seiko fan. I presently have two Titanium (Asian market only) Samurai's. My Blue Sammy, was a "go to" watch, for its "do all, go anywhere" capabilities. However, with wearing a watch, comes the occasional ding or scratch. Especially Sekio/Citizen Ti that scratches if you look at it funny. It was decided, lets give this watch a well deserved refreshing. Using the Omega Titanium Refinishing pad (Ofrei), fiberglass scratch brush (Ofrei), and 1500 grit wet/dry sand paper, the Ti restored to like new. Also, Seiko uses "Hardlux" crystals in most of their sport watches instead of the tougher more scratch resistant Sapphire. I acquired a Sapphire, slight dome, AR Crystal from Yobokies. Below are the results. Before: Scratched lugs, bracelet and original hardlux crystal LUG SCRATCHED AT 5:00 BEFORE Bracelet Desk Divers BEFORE ORIGINAL CRYSTAL After : Sapphire AR dome crystal Refinished case and bracelet little squiggle is dust... No more big scratch @ 5: lug, New Crystal installed Lume Re-Finished product. Full on direct sunlight - "FIGHT THE POWER!!!" Direct Sunlight!!! Gorgeous dial, shape-shifter. Back in the shade, love the slight dome. Titanium while it scratches easy, also restores easily! Thanks for looking.

Even then, it is only necessary to fast forward to good parts...

Missed it, looks likes video removed for copyright infringement.

Dreamworks

Octoberfest

E x c e l l e n t ! ! ! How a bout a detailed parts / build sheet?

Glock

I actually went ahead and pre-paid in full with BK. That reserved me a spot toward the top of the list once they start rolling off the bench. However, now you guys have me spooked.

Excellent as always R!!! Dial is phenomenal.

@Freddy333 your 6542's are hard to beat though!

Until my nearly Gen 1680 is assembled, or my 1665 project completed-- based on my current Collection: Favorite Gen: Favorite Rep "to look at": Favorite Rep "to Wear" Disclaimer, I am subject to change my mind at any second.

I say bring it Miyota. My 1995 Submariner REP was powered by a Gen Japanese Miyota. 15 years later, no service, it still runs. Kept +6 seconds accuracy for the first 13 years. Personally, as long as it is a reliable mechanical movement, I could care less whether it is Swiss, Chinese, Japanese or Russian. I do think a Japan gets closest. (Seiko, Citizen, etc are rock solid)

20mm is generally 20mm, but the holes in the case may complicate its fitting. Where the endlink meets the head. the curved portion. Try it and report back...