watcher

That is the sweeteast franken I have ever seen and will ever see!! I thought you had bought a gen at first!! Enjoy this beauty. The Zigmeister is a very impressive guy too!

Just cannot stop wearing my franken UPO or modding it for that matter!!. It will have a gen Rubber strap tomorrow for a change and soon it will hopefully have it's gen caseback fitted too!

My caseback is waiting for me at home but I'm away on holiday until later this month sometime but I will update when I have chance to try it and compare.

I had a white 968 CS back in 1993 when it was new and to me it is still the best driver's Porsche I've ever owned or driven. The balance of the chassis and the gearchange were superb and I really miss that car! I will try and find some pics for you my friend! I have owned 7 different Porsche models over the years including a 928 S4 auto among them and only my current 997 C4S comes close to the 968 for fun and poise! The 928 was a nice cruising car but not well balanced for spirited driving through tight hairpins!! more suited to driving to the South of France!! Hope that helps!

$118 for the case back. Taken 3 weeks to get it for me.

Thank guys! I have 10 watches with bezels and never turn any of them and they are all on genuine watches, not reps! Ofrei shipped my genuine caseback today so I will mkae comment on the fit later. On holiday now for a while so it will be quite some time before I see the caseback!

I use a blade on my swiss army knife but you have to use tape so you don't mark the case. It's not too hard to remove if you are patient with it.

I purchased the bezel complete! In fact the rep bezel was annoying me so much that I have now sacrificed the rotating action and I have bonded the gen bezel and insert to the case!!! I don't care about the bezel function and prefer a more visually accurate watch. The rep bezel just was not quite there for me. Here is a pic with gen bezel fitted.

This today and most days at the moment!

Gen end links are on ofrei website priced at $59 each. You need 951 parts.

My new favourite for a while!

Thanks for the compliments guys! I'm quite proud of this one! To sum up - Gen Parts are as follows: Dial Hands Crystal Bezel Insert Crown and Tube Bracelet End Links Date Wheel This is based on a Swiss ETA 2824-2 UPO supplied by Precioustime. The bracelet that came on the watch has gone down in quality over the last couple of years since my last UPO project! Poor finsih and poor engraving on the claps too. Luckily I had the older bracelet which has a very well engraved clasp and smooth finished links too. The Genuine end links are definately worth the $59 each price tag. They are better finshed and better profiled than the rep links. Omega pins are thicker though so I had to drill out the holes slightly more on the bracelet to fit. Another thing that bugs me is the crystal height on this particular watch, the insert sits slightly above the crystal edge on both rep and gen inserts so maybe the rehaut is a little too low. Both crystals are the same thickness so I cannot blame that. The gen bezel is the same thickness as the rep example. As for fitting a gen bezel, this is not possible without machining a shim with a lip on it to make up the thickness between the gen and rep bezel. A shame! The gen end links fit the case without having to bend the pins(22 x 1.8mm used) so the rep EL's must not be drilled perfectly as they were very bent on my watch! My genuine caseback will not arrive for a couple of weeks yet so I will update then on how that fits. Think that sums it up for now. Cheers

Cheers Buddy! Likewise, Noobfactory made a very good GMT!

My BP5004 on a BOB Caf Strap.

Finished building my UPO franken late last night so here are a few quick pics. More on what's been done later.

I will find the number for the gasket. You do not grease that.

I will have a good look at why the bezel will not fit when the watch arrives. Tried to find some hard evidence pics on here about that but could not find any.

I think most guys use a narrow file and push into the tube and twist and with a bit of luck it will come out without much hassle. Not got my watch yet(long story!) so cannot say for sure. I use Permatex Cold Weld bonding compound for fixing things like tubes but other strong adhesives will work too. Ofrei have informed me that my caseback is on order but not sure when it will arrive. Did you fit the gen end links too? Here is a pic of my parts list so far! Spare UPO bracelet with gen end links fitted Gen Bezel Assembly(not sure yet about fitting options) Gen dial Gen Hands Gen Gasket Gen Crystal Gen Crown Gen Tube Gen DW

Looks good pal! Have you fitted the crown and tube yet?

You are not telling us anything we do not already know and your dealings with the CC company may not help either. I fully understand your situation but some here have been waiting longer than that and know it is par for the course with George. A shame you did not read some of th erelated posts before your actions were taken.

Im waiting for a Planet Ocean as we speak from Precioustime and the watch you are looking for is known around here as the UPO. This is the large 45mm size and will accept all genuine parts without modification with exception of the bezel assembly. Have a good look through the Omega section and all your questions will be answered. Cousins in the UK sell all the parts for the UPO and no customs worries to Germany!

I've just got one of these from Cousins, not sure why they chose green though!

I received mine a few days ago along with a tube and it looks great! Not got a watch for it though! Can't decide which one to get yet.

Will do but I would have thought not looking at pics of both sizes on watches.

My pleasure! Still no watch from PT! nearly 3 weeks now. Looking at all my gens parts and itching to build!!!