Champagnesky

Hi! Does anyone have the 3d print files for the DWO tool and dial feet tool that has been circulating the forums a couple of years ago?

God damn, one of my grails Skickat från min iPhone med Tapatalk

I have the dw dial and the issue is that the subdials are not correctly recessed. Skickat från min iPhone med Tapatalk

Rubys is 680 dollars btw

thx, the problem is that the retention ring and the bezel ring sit very tight together on the 1665 and they pop out in one piece.

Great job here jmb, i see that you used 2 drill sizes. I assume that you did the smaller hole first? I actually want to lathe a he valve, ive got the specs from yukis site so making it wont be a problem, and I guess that the piece holding it on the other side is made of brass, so should not be a problem making one. Dont really know if the cartel case is gen spec for holding a gen movement in the future, do you have any info on this?

As the topic says, have anyone tried it?

thx, i think i may be missing the ring, how do i remove the outer ring, it sits so tight?

ok thx mate! Then I know... Yeah, ive seen those on cousins, but buying a gen case would be too easy and it would not be a franken....

Hi! Ive been wanting to do a franken vintage 300 for a long time, considering that the 565 movements are pretty affordable it sounded like a nice project. Ive been in touch with another member on another forum who purchased a sillix rep and a gen dial and caseback. Unfortunately the gen dial and caseback had different sizes that the sillix one and were basically too small to fit. So using a sillix midcase kinda falls of. There are also cartel reps of the 300 out there, if anyone has one, could you measure the dial width and the caseback width to see if gen parts will fit? the sizes of the parts are: Sillix dial: 30.90mm gen dial: 27.50mm Sillix caseback: 34.97mm gen caseback: 34.16mm

Actually struggling with PPetes DWO in my 1665 build, the dw is too high and gets stuck, even with a dial spacer.

thx, have been looking for this, will be printing tomorrow

The bezel is pretty loose on my 1665, any ideas on how to tighten it?

What DWO did you use?

Would laser cutting a dw be a solution? if the dws would be printed on thin pla?

Looks great! Always nice to see a clean 5517 build.

Great info thx!

Thx! You are right, it just felt so good that i Could Do a super clean build without cutting feet and looking for more parts Skickat från min iPhone med Tapatalk

Skickat från min iPhone med Tapatalk

damn those printed dials u do are really nice mate. Great build, real eyecandy

so clean! what case is this btw?

thx for the quick reply. I was completely sure they were the same diameter and height. The info i found on the 3035 was: Data 12.5''', Dm= 28.1mm, Do= 28.5mm H= 6.15mm (rotor stud +0.15mm) F= 2.05mm T= 2.15mm 27 jewels f = 28800 A/h power reserve 50h Hands 1.40 x 1.00 x 0.18mm and the 3135 is a little shorter, cant find any info on stem height etc. hands.

Hi! Does anyone know if the 3135 has the same dimensions as 3035? I have gen parts for a datejust 16013 build, case, dw, dial, hands. Was thinking about putting a sh3135 into it. Does anyone know if its possible to get the movement separately?

Just saw this thread, is it worth ditching my tc v6 and get the JF instead? Skickat från min iPhone med Tapatalk

Looks great. What movement will you be using in these? Skickat från min iPhone med Tapatalk