lhooq Posted May 23, 2012 Report Share Posted May 23, 2012 So I finally decided to go with a modern Sub and ordered one of TC's insert-less V4 16610s. At the same time, I was able to source a genuine 16610 insert from a friend. Both the watch and the insert arrived today. Unfortunately, I can't get them to get together. Off the case, the insert snaps into the bezel ring perfectly. But once the bezel is pressed onto the mid-case, pop goes the insert! It seems like the metal lip around the crystal is pushing against the inner edge of the insert. I have zero experience with modern Submariners, so I have to ask some basic questions: Is this normal? When I read about people working their thumbs around the circumference of the insert, are they doing this while the bezel is already mounted? Right now, my thumbs and fingertips are killing me. They haven't felt this awful since the time I mounted a particularly tight set of wire-bead Specialized cyclocross tires on my bicycle's rims. "Shut the door! I'm naked!" Link to comment Share on other sites More sharing options...
sneed12 Posted May 23, 2012 Report Share Posted May 23, 2012 Not uncommon. The usual fix is to shave the bottom of the gen insert slightly. Link to comment Share on other sites More sharing options...
alligoat Posted May 23, 2012 Report Share Posted May 23, 2012 Here you go M, straight from RWI! http://www.replica-watch.info/vb/showthread.php/not-so-easy-103880.html Like Sneed says, filing the bottom is one approach, and this discussion will also help. It's the typical deal- chinese aftermarket parts don't always fit like they should! Link to comment Share on other sites More sharing options...
lhooq Posted May 23, 2012 Author Report Share Posted May 23, 2012 Thanks, sneed and M! I'll bring the insert in for a shave and see how it goes tomorrow. Other than that issue, it's a remarkable out-of-the-box rep. It's tempting to respond with, "It better be, for that price" until I remember how much guys were willing to spend on WM9s not too long ago. Never thought I'd be a modern Sub guy, but I believed the hype! And you'd better believe the hype! (Except for the bit about the gen inserts fitting unmodified...) Link to comment Share on other sites More sharing options...
woof* Posted May 23, 2012 Report Share Posted May 23, 2012 M, Are you saying the inner dimension of the insert is touching the crystal/retainer and popping out the insert? I'm thinking if you can get the insert to snap into the bezel...while the bezel is off the watch...but then installing the bezel/insert...the insert pops out...might be a different problem. Many have had issues gettin inserts mounted because really tight fit, but thats different than your problem. To be sure, you know for fact you have a 16610 insert and not a 14060 or 16660? The latter two are different sizes inner diameter. Oh...and congrats! Link to comment Share on other sites More sharing options...
lhooq Posted May 23, 2012 Author Report Share Posted May 23, 2012 To be sure, you know for fact you have a 16610 insert and not a 14060 or 16660? My source is unimpeachable (and a few posts up the page, actually). And thanks! It's nice to go modern for a change. But don't expect me with a ceramic Sub anytime soon! Link to comment Share on other sites More sharing options...
cib0rgman Posted May 23, 2012 Report Share Posted May 23, 2012 this is strange, I have a TC sub with a Gen Insert and fits juits fine no filing at all. Are you sure the insert is Gen? Link to comment Share on other sites More sharing options...
Ephry73 Posted May 23, 2012 Report Share Posted May 23, 2012 Looking good M! The insert if it's gen a slight Filing should help. I did this for a few SSDs. Post pictures when you're done. Link to comment Share on other sites More sharing options...
jasf2002 Posted May 23, 2012 Report Share Posted May 23, 2012 Strange - the TW best crystal retaining ring does this but the TC one is lower profile so should not have this issue. I guess the tolerance may not be consistent and you are suffering from that - I shaved the inside of an insert gradually on a TW best and eventually it fitted fine so that solution sounds valid. Link to comment Share on other sites More sharing options...
the_rymeister Posted May 23, 2012 Report Share Posted May 23, 2012 I had a similar problem when trying to fit gen insert to my tc sub, I tried and tried and the ......snap broke the gen insert straight through the triangle which holds the pearl, ended up buying a brand new insert and very slightly sanding around edge and now it pops in and out with a little tension Link to comment Share on other sites More sharing options...
cougar1 Posted May 23, 2012 Report Share Posted May 23, 2012 Had to do it recently, tried a first attempt and sods law says it was a no go...as expected. I then followed the Rymeisters lead and got out the 1600 grit emery. Went around a few times ...no go kept going doing a couple of revolutions around the emery with the insert and testing again. At one stage I was tempted to just pull out the heavy grit but thought no just keep going as it can't be too far away. Well I kept going with the 1600 for about 20 mins testing it after every few revolutions, at one stage I thought I'm gonna ballss this up but eventually it snapped in very securely and looks great now. This with an absolute 110% gen insert. Was cursing it at the time but happy now. So much for straight on click in fit, no way! Link to comment Share on other sites More sharing options...
the_rymeister Posted May 23, 2012 Report Share Posted May 23, 2012 Had to do it recently, tried a first attempt and sods law says it was a no go...as expected. I then followed the Rymeisters lead and got out the 1600 grit emery. Went around a few times ...no go kept going doing a couple of revolutions around the emery with the insert and testing again. At one stage I was tempted to just pull out the heavy grit but thought no just keep going as it can't be too far away. Well I kept going with the 1600 for about 20 mins testing it after every few revolutions, at one stage I thought I'm gonna ballss this up but eventually it snapped in very securely and looks great now. This with an absolute 110% gen insert. Was cursing it at the time but happy now. So much for straight on click in fit, no way! Lol I was cursing my insert the whole time when sanding it and thought the exact same thing about busting out the coarse paper Link to comment Share on other sites More sharing options...
highoeyazmuhudee Posted May 23, 2012 Report Share Posted May 23, 2012 same thing happened on the old 1:1 16610 MBW subs, retianing ring was pushing it back out once installed, problem was the bezel ring was too short in height to allow the insert to sit above the retaining ring once installed. i doubt this is whats happening here with the TC but something worth eliminating as a possibility Link to comment Share on other sites More sharing options...
cougar1 Posted May 23, 2012 Report Share Posted May 23, 2012 Lol I was cursing my insert the whole time when sanding it and thought the exact same thing about busting out the coarse paper I'm grateful to you Ry that you cleared up that it needed to be sanded earlier.. (although at the cost to you of a perfectly good insert ,which was a bloody shame.) if I hadn't expected that it needed to be sanded I'm absolutely sure I would've broken mine trying to force it in aswell....it was a bugger to fit! Link to comment Share on other sites More sharing options...
mymanmatt Posted May 24, 2012 Report Share Posted May 24, 2012 when this happens it is because the crystal diameter is a touch wide. Make sure the insert will fit over the crystal. You can change the crystal and maybe find one, a thousandth or 2 smaller than the one on the watch. If not you will have to trim the inside diameter of the insert. Good luck Link to comment Share on other sites More sharing options...
lhooq Posted May 24, 2012 Author Report Share Posted May 24, 2012 Urgh... Here comes the heartbreak. I left the Sub and the insert with my watchsmith today with the instructions to make them fit. I returned to find that he'd taken a not insignificant bit of metal off the inner edge of the gen insert. Too upset with myself to even search for the banging-head-on-the-wall emoticon... Link to comment Share on other sites More sharing options...
sneed12 Posted May 24, 2012 Report Share Posted May 24, 2012 Holy crap dude... I'm sorry. If you want to send it to me when you source another gen insert, I'll fit it for you (for free), and I guarantee it won't look like that. Link to comment Share on other sites More sharing options...
lhooq Posted May 24, 2012 Author Report Share Posted May 24, 2012 sneed12: Thanks for your kind offer. I'd take you up on it, but I get an error message when I try to send you a PM. Link to comment Share on other sites More sharing options...
sneed12 Posted May 24, 2012 Report Share Posted May 24, 2012 sneed12: Thanks for your kind offer. I'd take you up on it, but I get an error message when I try to send you a PM. Ah yes, my VIP expired a few days ago and I haven't made the payment yet. Try again in a couple of minutes. Link to comment Share on other sites More sharing options...
Ephry73 Posted May 24, 2012 Report Share Posted May 24, 2012 I wonder if that insert is from the same batch that Startime is selling as gen inserts. I bought one to test from them and it is very much the same insert you show here and a pain to fit around the crystal. Have you tried a used gen to fit? E Link to comment Share on other sites More sharing options...
janeto72 Posted May 24, 2012 Report Share Posted May 24, 2012 i'm going to chime in here.....i wish i had seen this sooner. The TC bezel assembly is designed to work with a gen insert. There are some +/- to the tolerence around the inner diameter of the bezel. Some gen 16610 inserts will pop right in with no mods and some need a little sanding around the outer edge only. I have only seen two bezel assemblies with the TC subs. The first has shallow teeth and the second has more deeper ones. They are both built the same.Just from a different batch. I have measured them with electronic calipers.You should never have to grind the inside of your gen insert! You have the wrong insert my friend most likely for a non date sub or seadweller......The crystal that comes with the TC sub is gen spec and made to fit gen subs./gen sub construction. Link to comment Share on other sites More sharing options...
janeto72 Posted May 24, 2012 Report Share Posted May 24, 2012 you can try sanding down under the insert allow it to recess a bit or sand down the height of the retainung ring 1 mm. altough i have never hadto sand down a retaining ring to fit a gen insert on a TC Sub. Only on a TW sub. Link to comment Share on other sites More sharing options...
cib0rgman Posted May 24, 2012 Report Share Posted May 24, 2012 A true Gen insert will fit without modifications, at the begining is har to get to get in, start by putting in the side where the pearl is and work your way to the other end and use some kind of plastic piece or wood to press down at the end the insert, it is just hard but that the way it is. Link to comment Share on other sites More sharing options...
janeto72 Posted May 24, 2012 Report Share Posted May 24, 2012 another good option is the clark insert for the 16800....it fits nice with a little sanding around the outside diameter and the pearl is not bad either except for the very poor lume.$14.30 from Gary Clark on ebay ..nostalgia2000... is his ebay handle. Link to comment Share on other sites More sharing options...
lhooq Posted May 24, 2012 Author Report Share Posted May 24, 2012 A true Gen insert will fit without modifications, at the begining is har to get to get in, start by putting in the side where the pearl is and work your way to the other end and use some kind of plastic piece or wood to press down at the end the insert, it is just hard but that the way it is. I'd read about your efforts prior to starting this thread, and, in fact, one of my remarks referred to them: "When I read about people working their thumbs around the circumference of the insert, are they doing this while the bezel is already mounted?" The thing with my Sub is that the gen insert will snap on perfectly when the bezel is off the case. Once the bezel is pressed on, the insert pops off. So, are you fitting your insert after you've mounted the bezel, or while it's off the watch? I have measured them with electronic calipers.You should never have to grind the inside of your gen insert! You have the wrong insert my friend most likely for a non date sub or seadweller......The crystal that comes with the TC sub is gen spec and made to fit gen subs./gen sub construction. Could you share some of your measurements? I would like to confirm that the problem is my insert, and not my TC Sub. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now