Ephry73

Some older TC bracelets DO fit better. This is a V2/V3 hybrid on an old BK Wm9 v3 case with M serial you can see how there is almost no recess from the top of the lug to the top of the SEL. The watch is sporting gen insert, gen crystal, gen crown on BK tube, gen gaskets all throughout, with a BK dial and a mix of TC and ST hands on a high-beat asian movement for no issues with the date wheel. Not as much as a TC by any chance, but I build it from parts I had laying around. It is possible to build a nice, gen spec, or gen like Sub that can be worn daily and that will be waterproof and will also look great on the wrist. Because of how slim the case is I am tempted to go drill-through lugs for an early 16610 build.

Bump with interest E

The one on that picture looks more like the 214270(correction) which is bigger. I built one of these not too long ago, but the dial was an issue and had to go custom as th case actually takes a 29.5mm to 30mm dial most dials only come in 29mm max E

You can always use one of the early 14270 cases with lugholes to start and go from there. The hands and dial on those 14270s with eta could be relumed to keep it simple. I build something like this for my wife in late 2013 and looks too good for the money spent. The bracelet that comes in those eta 14270s is not the best, but on a NATO strap no one cares and looks super good. Just a thought. The eta movement can be serviced and you can get a two-step keyless cover since you won't have a date to worry about to simplify operation and also make it more gen like. E

Any time brother.

You're correct.

I know this is an old thread, but I'm searching for 002A dials and hands for a build. Pro, Love your watch!!! E

I may have some screws that fit. Send me a pm red. E

I'm with HH on the call, although the center one could also be a TC

Waking this back up as I need at least three 93150 bracelets E

Very Nice Fitch! My 40 is probably one of the older ones and the CG is not as nice as that one. Easily fixed I bet E

Love it! The CG looks spot in also. Is that stock for that case set?

Not to mention all of the other issues that go with that, it's not just food, its the entire ecosystem. Without the funds, it's just basically a meal plan.

I liked his daytona yatch master dial better.

Well, if it is the same case it should definitely fit. I was told the case was an early Sean case and I went with that notion. I could not find anything to argue against it. I was ultimately going to use this case for an early 16610 transitional model as the rehaut seemed shallower than the 3135 cases (Both Late Sean and ST) and about the same as the ST3035 cases but the center line for the stem was closer to a 3135 case. Things changed and I had to sell it. There is about .4mm or less of difference on the top side of the 3035 and 3135 movements. I wonder if this is the issue here.

I'm not home yet, but OP if you can PM or post here lug pictures. I can compare the ones I have of the case. The ST case backs all fit on the case I sold Dutch and should fit gen with no issues. The case also fit a 3035 gen with no issues and I fitted a y3135 without a problem. Just had to use different movement to case screws.

I would not mind one of these in my watchbox. E

Moi moi

Some of the later cases could be use for both with a different case back.

St has them also. G, send me a PM if you can.

Unhu

I can't believe this is up to $102.50 already. It even has a wire-clip bezel!

Photo 3 is the better tell, wrong engraving ( etched not engraved) and has a T after the number. The case has lug holes so should have no T after model number.

There is no Thursday lol

Just trying on a different strap (wrong lug width 20mm) just for looks. I think i may get something like this in nylon or canvas as a permanent strap for the 3717.This one is a super soft 100+ yo leather from an English Boxing gym Speedball made by Donerix a few years back.